/en-s3-science-cells-life-processes-particle-model-separation-forces-pressure-circuits-electrical-power-energy-efficiency-heat-scientific-investigation-practice-paper/
/en-s3-science-cells-life-processes-particle-model-separation-forces-pressure-circuits-electrical-power-energy-efficiency-heat-scientific-investigation-practice-paper/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

S3 Integrated Science Practice Paper (Set 1): Cells, Particles, Forces, Circuits and Energy

S3 Integrated Science Practice Paper (Set 1): Cells, Particles, Forces, Circuits and Energy

  • 2026-11-23

S3 Science

S3 Integrated Science practice paper Set 1: cells and life processes, particle model, separation, forces, pressure, electric circuits and energy, with full worked answers.

Paper details S3 Integrated Science practice paper Set 1: cells and life processes, the particle model and separation methods, forces and pressure, electric circuits and power, energy efficiency and heat, scientific investigation, with full worked answers.

Section A: Cells and Life Processes (16 marks)

Show your working and give the units.

# Question Answer and marking notes
1 (a) A microscope has a x10 eyepiece and a x40 objective. (i) Find the total magnification. (ii) A cell appears 20 mm long under this microscope. Find its actual length in mm. (i) Total magnification = 10 x 40 = 400; (ii) actual length = 20 / 400 = 1/20 mm (50 um).
2 (b) The field of view under low power is 1.8 mm across. If one cell has a diameter of 0.06 mm, how many cells fit across the diameter of the field? Number of cells = 1.8 / 0.06 = 30.
3 (c) A cell divides once every 30 minutes. Starting from one cell, how many cells are there after 2 hours? 2 hours = 120 minutes, so there are 4 divisions; number of cells = 2^4 = 16.
4 (d) A leaf has a surface area of 2.5 cm^2 and carries 1,200 stomata. Find the average number of stomata per cm^2. Stomata per cm^2 = 1200 / 2.5 = 480.

Section B: Particle Model and Separation (16 marks)

Use scientific vocabulary in explanations and show working in calculations.

# Question Answer and marking notes
5 (a) A stone has a mass of 78 g and a volume of 30 cm^3. (i) Find its density. (ii) Water has a density of 1.0 g/cm^3. State whether the stone floats or sinks and explain. (i) Density = 78 / 30 = 13/5 g/cm^3; (ii) its density is greater than that of water (1.0 g/cm^3), so it is heavier than the same volume of water and sinks.
6 (b) Sand is stirred into salt solution. Describe how filtration and distillation can be used to separate the sand, the salt and the water, and state the principle of each step. Filter first: sand is insoluble and its particles are too large to pass the filter paper, so it stays as the residue while salt solution passes through as the filtrate. Then distil the filtrate: water boils off, condenses in the condenser and is collected as distilled water, while the salt, which has a much higher boiling point, remains behind.
7 (c) A beaker of water is heated from 20 °C to 80 °C, the temperature rising by 5 °C each minute. Find the time needed. Temperature rise = 80 – 20 = 60 °C; time = 60 / 5 = 12 minutes.
8 (d) 500 cm^3 of salt solution contains 25 g of salt. Find its concentration in g/dm^3. 500 cm^3 = 0.5 dm^3; concentration = 25 / 0.5 = 50 g/dm^3.

Section C: Forces, Pressure and Motion (16 marks)

Take g = 10 m/s^2.

# Question Answer and marking notes
9 (a) A 4 kg trolley on a smooth bench is pushed by a horizontal resultant force and accelerates at 3 m/s^2. Find the resultant force. F = ma = 4 x 3 = 12 N.
10 (b) A force of 240 N acts perpendicularly on an area of 0.04 m^2. Find the pressure in Pa and in kPa. Pressure = 240 / 0.04 = 6000 Pa = 6 kPa.
11 (c) A runner covers 120 m in 15 s. Find the average speed in m/s and in km/h. Average speed = 120 / 15 = 8 m/s = 8 x 3.6 = 144/5 km/h.
12 (d) A block of wood of density 0.6 g/cm^3 floats on water. Find the percentage of its volume that is submerged. Fraction submerged = 0.6 / 1.0 = 0.6, that is 60%.

Section D: Circuits and Electrical Power (16 marks)

Show working and units.

# Question Answer and marking notes
13 (a) A 6 ohm resistor is connected to a 12 V supply. Find the current through it. I = V / R = 12 / 6 = 2 A.
14 (b) Using (a), the resistor is switched on for 5 minutes. (i) Find its power. (ii) Find the energy it uses, in J. (i) P = VI = 12 x 2 = 24 W; (ii) E = Pt = 24 x 300 = 7200 J.
15 (c) A 4 ohm and a 6 ohm resistor are connected in series to a 6 V supply. Find (i) the total resistance, (ii) the current, (iii) the voltage across each resistor. (i) R = 4 + 6 = 10 ohm; (ii) I = 6 / 10 = 3/5 A; (iii) 12/5 V across the 4 ohm resistor and 18/5 V across the 6 ohm resistor (6 V in total).
16 (d) A 60 W lamp is left on for 4 hours. Find the electrical energy it uses in kWh. E = 60 x 4 / 1000 = 6/25 kWh.

Section E: Energy, Efficiency and Heat (16 marks)

Take g = 10 m/s^2 and the specific heat capacity of water as 4200 J/(kg °C).

# Question Answer and marking notes
17 (a) A 2 kg object falls from rest through 5 m, air resistance being negligible. (i) Find the gravitational potential energy lost. (ii) Find its speed on reaching the ground. (i) PE lost = mgh = 2 x 10 x 5 = 100 J; (ii) all of it becomes kinetic energy: 0.5mv^2 = 100 J, so v = sqrt(2 x 100 / 2) = 10 m/s.
18 (b) A machine takes in 500 J of energy and delivers 175 J of useful output; the rest is lost as heat and sound. Find its efficiency. Efficiency = 175 / 500 x 100% = 35%.
19 (c) 0.5 kg of water is heated from 20 °C to 60 °C. (i) Find the energy absorbed, in kJ. (ii) A metal block of the same mass heated in the same way warms up faster than water; explain this in terms of specific heat capacity. (i) E = mc(dT) = 0.5 x 4200 x 40 = 84000 J = 84 kJ; (ii) the metal has a smaller specific heat capacity than water, so it needs less energy to gain the same temperature rise and therefore warms up faster for the same heating rate.

Section F: Scientific Investigation and Data (20 marks)

In the design question state the hypothesis, controlled variables, measurements and data handling.

# Question Answer and marking notes
20 (a) A student obtains g = 10.4 m/s^2 in a pendulum experiment; the accepted value is 10.0 m/s^2. (i) Find the percentage error. (ii) Suggest one way to reduce random error. (i) Error = (10.4 – 10.0) / 10.0 x 100% = 4%; (ii) repeat the measurement several times and take the average, which reduces random error.
21 (b) Design an experiment to investigate how the surface area of water affects the rate of evaporation. State the hypothesis, two variables to keep constant, how the rate of evaporation is measured, and why the test is repeated three times. Hypothesis: the larger the surface area, the faster the rate of evaporation. Controlled variables: start with the same volume and temperature of water and keep air movement, humidity and room temperature constant. Measurement: use identical containers with the same volume of water and record the loss in mass on an electronic balance every 10 minutes for different mouth areas. Repeating three times and averaging reduces random error and makes the result more reliable.
22 (c) A car covers 300 m in the first 20 s and a further 900 m in the next 30 s. Find (i) the average speed of the first stage, (ii) that of the second stage, (iii) the average speed for the whole journey. (i) 15 m/s; (ii) 30 m/s; (iii) whole journey (300 + 900) / (20 + 30) = 24 m/s (not the mean of the two speeds, 22.5 m/s).

Find a tutor — freeTutor Registration →

A TutorZone practice paper; original questions and passages, not publisher material.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →