S5 DAT Practice Paper | Drawing scale, tolerances, RC circuits, cooling and 3D printing costs
- 2026-11-18
Design and Applied Technology – engineering design
S5 DAT practice paper: drawing scale, tolerances and fits, bolt shear, bearing friction, RC timing, capacitor energy, LED resistors, heat sinks and 3D print costing.
Download Question paper PDF | Answer key PDF
Paper details S5 Design and Applied Technology practice paper with answers on projection scale, hole and shaft limits, bolt shear, RC time constants, LED resistors, heat sinks and 3D printing costs.
Part A Projection drawing, scale and sheet capacity
Question 1 (16 marks)
| # | Question | Answer and marking notes |
|---|---|---|
| 1 | A part 2 400 mm long is drawn at a scale of 1:20. Find its length on the drawing in mm. | Length on drawing = 2400 / 20 = 120 mm. |
| 2 | A plan is drawn at 1:50 and the area on paper is 84 cm2. Find the actual area in m2. | The area ratio is 50 squared = 2500, so actual area = 84 x 2500 = 210 000 cm2 = 21 m2. |
| 3 | The usable drawing area is 400 mm by 280 mm at a scale of 1:10. Find the largest diameter that can be drawn in full, in m. | The short side of 280 mm limits it: 280 x 10 = 2800 mm, that is 2.8 m. |
| 4 | A part is drawn at 2:1 and measures 150 mm on paper with a tolerance of +/-0.4 mm marked. Find the real length and real tolerance in mm. | Real length = 150 / 2 = 75 mm and the real tolerance is +/-0.4 / 2 = +/-0.2 mm. |
Part B Tolerances, fits and fasteners
Question 2 (15 marks)
| # | Question | Answer and marking notes |
|---|---|---|
| 5 | A hole is 24.000 to 24.021 mm and the shaft is 23.979 to 24.000 mm. Find the maximum and minimum clearance in mm and name the class of fit. | Maximum clearance = 24.021 – 23.979 = 0.042 mm; minimum clearance = 24.000 – 24.000 = 0 mm, so this is a transition fit. |
| 6 | For the same limits, find the tolerance zone of the hole and of the shaft in mm and say whether they are equal. | Hole tolerance = 24.021 – 24.000 = 0.021 mm and shaft tolerance = 24.000 – 23.979 = 0.021 mm, so both are equal at 0.021 mm. |
| 7 | At a basic size of 30 mm, IT7 is 21 micrometres and IT8 is 33 micrometres. Find the ratio of IT8 to IT7. | Ratio = 33 / 21 = 1.57, so IT8 is about 1.57 times IT7. |
| 8 | In a batch of 200 parts the reject rate is 2% and each good part earns $45. Find the number of good parts and the total profit. | Good parts = 200 x 0.98 = 196 and total profit = 196 x 45 = $8,820. |
Part C RC charging and LED circuits
Question 3 (18 marks)
| # | Question | Answer and marking notes |
|---|---|---|
| 9 | A resistor of 10 kohm is in series with a 470 microfarad capacitor. Find the time constant in seconds. | Time constant = RC = 10 000 x 470 x 10^-6 = 4.7 s. |
| 10 | A 9 V supply charges the capacitor through the resistor. Find the capacitor voltage at one time constant and the time taken to reach it. | At one time constant the voltage is 0.632 x 9 = 5.688 V and the time is 4.7 s. |
| 11 | Find the time for five time constants in seconds and state roughly what percentage of full charge has been reached. | Five time constants take 5 x 4.7 = 23.5 s, by which the capacitor is about 99.3% charged and is treated as fully charged. |
| 12 | A 5 V supply drives an LED with a forward drop of 2.1 V at 20 mA. Find the series resistor in ohms and the power it dissipates in mW. | Resistance = (5 – 2.1) / 0.02 = 145 ohm and power = 2.9 x 0.02 = 0.058 W, that is 58 mW. |
Part D Capacitor energy and battery capacity
Question 4 (16 marks)
| # | Question | Answer and marking notes |
|---|---|---|
| 13 | A 470 microfarad capacitor is charged to 9 V. Find the stored energy in mJ to three significant figures. | Energy = 0.5 x 470 x 10^-6 x 81 = 0.019035 J, that is 19.0 mJ. |
| 14 | If the voltage is raised to 18 V, what is the stored energy in mJ, and why? | Energy varies with the square of voltage, so doubling the voltage gives four times the energy: 19.0 x 4 = 76.1 mJ. |
| 15 | A 12 V, 2000 mAh battery is discharged at a constant 0.5 A. Find the running time in hours and the total energy in Wh. | Running time = 2000 mAh / 500 mA = 4 h and energy = 12 x 2 = 24 Wh. |
| 16 | The same battery has a discharge efficiency of 85%. Find the usable energy in Wh and in J. | Usable energy = 24 x 0.85 = 20.4 Wh = 20.4 x 3600 = 73,440 J. |
Part E Heat sinks, thermal resistance and power
Question 5 (17 marks)
| # | Question | Answer and marking notes |
|---|---|---|
| 17 | A component dissipates 5 W with a thermal resistance of 6 degC per W in a 30 degC environment. Find the temperature rise and the component temperature. | Rise = 5 x 6 = 30 degC, so the component runs at 30 + 30 = 60 degC. |
| 18 | With a heat sink the thermal resistance falls to 2.5 degC per W while dissipation rises to 8 W at the same 30 degC ambient. Find the new temperature. | Rise = 8 x 2.5 = 20 degC, so the new temperature is 30 + 20 = 50 degC. |
| 19 | If the maximum junction temperature is 85 degC, the ambient is 35 degC and the dissipation is 6 W, find the largest allowable thermal resistance in degC per W. | Allowable resistance = (85 – 35) / 6 = 8.33 degC per W. |
| 20 | A cooling fan draws 0.15 A at 12 V while the chip dissipates 8 W. Find the fan power in W and its percentage of the chip dissipation. | Fan power = 0.15 x 12 = 1.8 W, which is 1.8 / 8 x 100 = 22.5% of the chip power. |
Part F 3D printing cost and pricing
Question 6 (18 marks)
| # | Question | Answer and marking notes |
|---|---|---|
| 21 | A model has a volume of 12 cm3 and PLA has a density of 1.24 g/cm3. Find the mass of filament used in g. | Mass = 12 x 1.24 = 14.88 g. |
| 22 | Filament costs $180 per kg. Find the material cost of that model in dollars to two decimals. | Cost per gram is 180 / 1000 = $0.18, so material cost = 14.88 x 0.18 = $2.68. |
| 23 | Printing takes 2.5 hours at $12 per machine hour, plus 10% extra material for failed prints. Find the total cost to two decimals. | Machine time = 2.5 x 12 = $30.00, material with 10% extra = 2.68 x 1.10 = $2.95, so the total is $32.95. |
| 24 | To achieve a 35% gross margin, find the selling price in dollars to two decimals. | Selling price = 32.95 / (1 – 0.35) = $50.69. |
Find a tutor — freeTutor Registration →
A TutorZone practice paper; original questions and passages, not publisher material.



