/en-s6-dat-structures-mechanics-gearing-torque-power-electronics-rc-opamp-materials-manufacturing-energy-efficiency-ergonomics-practice-paper/
/en-s6-dat-structures-mechanics-gearing-torque-power-electronics-rc-opamp-materials-manufacturing-energy-efficiency-ergonomics-practice-paper/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

S6 Design and Applied Technology Practice Paper: Structures and Mechanics, Gears and Power Transmission, Electronics and Control, Materials and Manufacturing, Energy Systems, Design Analysis and Ergonomics (100 marks)

S6 Design and Applied Technology Practice Paper: Structures and Mechanics, Gears and Power Transmission, Electronics and Control, Materials and Manufacturing, Energy Systems, Design Analysis and Ergonomics (100 marks)

  • 2026-11-21

Design and Applied Technology · S6

S6 DAT practice paper: 24 questions, 100 marks, 75 minutes on structures, gears, electronics, materials, energy and costing, with every figure computed in Python.

Paper details S6 Design and Applied Technology practice paper with full answer key: 24 questions, 100 marks on structures, mechanisms, electronics, materials, energy and costing.

Part 1 Structures and Mechanics (16 marks)

Show all formulae, substitutions and calculation steps.

# Question Answer and marking notes
1 A steel rod 2.0 m long has a cross-sectional area of 250 mm2 and carries a 50 kN tensile load. Find the tensile stress in MPa. Stress = force / area = 50000 / 250 = 200 MPa.
2 The same rod extends by 1.2 mm. Find the strain (decimal) and the Young modulus in GPa to 1 decimal place. Strain = 1.2 / 2000 = 6.0e-04; Young modulus = stress / strain = 200 / 6.0e-04 = 333333 MPa = 333.3 GPa.
3 A rectangular beam is 50 mm wide and 100 mm deep. Find its second moment of area in mm4 to 3 significant figures, then the bending stress in MPa at 50 mm from the neutral axis when the maximum bending moment is 2.5 kNm. Second moment = 50 x 100^3 / 12 = 4.167e+06 mm4; bending stress = 2.5e6 x 50 / 4.167e+06 = 30 MPa.
4 The steel has an ultimate strength of 480 MPa and a working stress of 160 MPa. Find the factor of safety; if the working load is doubled, find the new factor and say whether it meets the usual requirement of at least 2. Factor of safety = 480 / 160 = 3.0; after doubling the load = 480 / 320 = 1.5, below 2, so the design fails and a larger section or stronger material is needed.

Part 2 Gears and Power Transmission (16 marks)

Give units for every power and efficiency answer and state significant figures.

# Question Answer and marking notes
5 Gear A has 20 teeth and runs at 900 rpm, driving gear B with 60 teeth. Find the gear ratio and the speed of gear B in rpm. Gear ratio = 60 / 20 = 3.0; speed of B = 900 / 3.0 = 300 rpm, a speed reduction with torque increase.
6 A motor delivers 12 Nm at 1450 rpm. Find its output power in watts (whole number) and in kW to 3 decimal places. Power = 2 pi N T / 60 = 2 pi x 1450 x 12 / 60 = 1822 W = 1.822 kW.
7 The motor drives a load through a gearbox of 85% efficiency. Find the gearbox output power in watts and the power lost in watts. Output = 1822 x 0.85 = 1549 W; loss = 1822 – 1549 = 273 W, mainly tooth friction and oil churning.
8 A screw jack has a 5 mm lead, an input torque of 8 Nm and 40% efficiency. Find the axial load it can raise in newtons (whole number) and in kN to 2 decimal places. Axial load = 2 pi T eta / lead = 2 pi x 8 x 0.40 / 0.005 = 4021 N = 4.02 kN.

Part 3 Electronics and Control Circuits (17 marks)

For electronics questions, describe the circuit and state the formulae used.

# Question Answer and marking notes
9 A 12 V supply is connected to 4 kohm and 8 kohm resistors in series. Find the current in mA and the voltage across the 8 kohm resistor in V. Total resistance = 12 kohm; current = 12 / 12000 = 1.0 mA; voltage across 8 kohm = 0.0010 x 8000 = 8 V.
10 A potential divider uses 10 kohm and 22 kohm resistors across a 12 V supply with no load. Find the output voltage across the 22 kohm resistor to 2 decimal places. Output = 12 x 22 / (10 + 22) = 12 x 22 / 32 = 8.25 V; the output falls once a load is connected.
11 A 47 kohm resistor and a 100 microfarad capacitor are in series across 12 V. Find the time constant in seconds (1 decimal place), the time to reach 63.2% of full charge, and the 5 time-constant time treated as fully charged. Time constant = 47000 x 100e-6 = 4.7 s; 63.2% is reached in one time constant = 4.7 s; five time constants = 23.5 s.
12 An inverting op-amp has a 100 kohm feedback resistor, a 10 kohm input resistor and ±12 V rails. Find the voltage gain, the output for a 0.25 V input, and say whether the output saturates. Gain = -Rf / Rin = -100 / 10 = -10; output = -10 x 0.25 = -2.5 V, which is 9.5 V inside the -12 V rail, so it is not saturated.

Part 4 Materials and Manufacturing (17 marks)

Use the units given in each material and machining question.

# Question Answer and marking notes
13 An aluminium plate measures 200 x 100 x 20 mm and aluminium has a density of 2700 kg/m3. Find the volume in m3 and the mass in kg to 2 decimal places. Volume = 0.2 x 0.1 x 0.02 = 4e-04 m3; mass = 4e-04 x 2700 = 1.08 kg.
14 A 25 m steel rail has a coefficient of linear expansion of 12e-6 per degree and sees a 40 degree temperature change. Find the change in length in mm (whole number) and explain why expansion gaps are needed. Expansion = 25 x 12e-6 x 40 = 12 mm; without a gap the rail would be in compression and could buckle, so expansion gaps or stressed continuously welded rail are used.
15 A milling cutter is 50 mm in diameter and runs at 1200 rpm. Find the cutting speed in m/min to 1 decimal place. Cutting speed = pi D N / 1000 = pi x 50 x 1200 / 1000 = 188.5 m/min.
16 The same cut uses 0.05 mm per tooth with 4 teeth. Find the feed rate in mm/min and the time to mill a 480 mm long workpiece in minutes to 1 decimal place. Feed rate = 0.05 x 4 x 1200 = 240 mm/min; time = 480 / 240 = 2.0 min.

Part 5 Energy System Efficiency (17 marks)

Separate input, output and losses in every energy answer.

# Question Answer and marking notes
17 A 1.6 m2 PV panel has 20% efficiency under 800 W/m2 irradiance. Find its instantaneous output in W. Output = 1.6 x 800 x 0.20 = 256 W.
18 The panel gets 5 effective sun hours a day and the home uses 3.2 kWh a day. Find the daily generation in kWh and the percentage of demand covered (whole number). Daily generation = 256 x 5 / 1000 = 1.28 kWh; coverage = 1.28 / 3.2 x 100 = 40%.
19 A 12 V 100 Ah battery is limited to 80% depth of discharge. Find the usable energy in kWh (2 decimal places) and how long it runs a 200 W load in hours (1 decimal place). Usable energy = 12 x 100 x 0.80 = 960 Wh = 0.96 kWh; run time = 960 / 200 = 4.8 h.
20 The PV system has 90% charging efficiency and a 92% efficient inverter. Find the overall system efficiency as a percentage (2 decimal places) and the AC output in W (whole number). Overall efficiency = 20% x 0.90 x 0.92 = 16.56%; AC output = 256 x 0.90 x 0.92 = 212 W, losing 44 W in total.

Part 6 Design Analysis and Ergonomics (17 marks)

State your assumptions and rounding for costing and ergonomics answers.

# Question Answer and marking notes
21 A part has a net mass of 0.35 kg, a scrap rate of 15% and material costing $48 per kg. Find the material consumed per part in kg (4 decimal places) and the material cost per part to 2 decimal places. Material used = 0.35 x 1.15 = 0.4025 kg; cost = 0.4025 x 48 = $19.32.
22 Tooling costs $120,000 for a batch of 5000 parts. Find the tooling cost per part and the total cost per part to 2 decimal places. Tooling per part = 120000 / 5000 = $24.00; total cost = 19.32 + 24.00 = $43.32.
23 The selling price is $65 per part. Find the profit per part, total profit and contribution margin as a percentage to 1 decimal place. Profit per part = 65 – 43.32 = $21.68; total = 21.68 x 5000 = $108,400; contribution margin = (65 – 19.32) / 65 = 70.3%.
24 User height for a product is normal with a mean of 170 cm and standard deviation of 6 cm. Find the 5th and 95th percentile heights in cm (1 decimal place, using z = ±1.645) and explain why the adjustable range is set this way. 5th percentile = 170 – 1.645 x 6 = 160.1 cm; 95th = 170 + 1.645 x 6 = 179.9 cm, covering about 90% of users; the remaining 5% tails are handled by adjustability or accessories instead of over-sizing every unit.

Find a tutor — freeTutor Registration →

A TutorZone practice paper; original questions and passages, not publisher material.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →