/en-s6-design-and-applied-technology-beam-bending-gear-train-tensile-stress-voltage-divider-breakeven-crank-slider-practice-paper/
/en-s6-design-and-applied-technology-beam-bending-gear-train-tensile-stress-voltage-divider-breakeven-crank-slider-practice-paper/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

S6 Design and Applied Technology Practice Paper (Set 1): Simply Supported Beam Reactions and Bending Stress, Two-stage Gear Ratios and Torque, Tensile Stress and Young Modulus, Series Voltage Divider, Product Cost Break-even, Crank-slider Motion and Production Rate

S6 Design and Applied Technology Practice Paper (Set 1): Simply Supported Beam Reactions and Bending Stress, Two-stage Gear Ratios and Torque, Tensile Stress and Young Modulus, Series Voltage Divider, Product Cost Break-even, Crank-slider Motion and Production Rate

  • 2026-11-22

DAT · S6

S6 DAT paper (set 1): 24 parts, 100 marks, 75 min on beam bending, gear ratios, tensile stress, voltage division, break-even cost and crank-slider motion, with answers.

Paper details S6 DAT practice paper: beam bending, gears, tensile stress, circuits, cost, mechanisms

Question 1: Reactions, Bending Stress and Section Design of a Simply Supported Beam (20 marks)

A simply supported beam of span 6 m carries a central point load of 12 kN. The rectangular cross-section is 100 mm wide and 200 mm deep. The ultimate bending stress of the material is 180 MPa and a safety factor of 3 is required.

# Question Answer and marking notes
1 Find the reaction at each support. Symmetrical simply supported beam, so each reaction is R = 12 / 2 = 6 kN.
2 Find the maximum bending moment at mid-span (kN m). The maximum moment is at mid-span: M = P L / 4 = 12 x 6 / 4 = 18 kN m.
3 Find the section modulus (mm3) and the maximum bending stress (MPa), and state whether the design is acceptable. Section modulus Z = b h^2 / 6 = 100 x 200^2 / 6 = 666 667 mm3. Bending stress = 18 x 10^6 / 666 667 = 27.0 MPa. Allowable stress = 180 / 3 = 60 MPa, so 27.0 MPa is acceptable; the actual factor of safety is 6.67.
4 If the central load rises to 30 kN, find the maximum bending stress and the minimum beam depth needed to stay within the allowable stress (width unchanged). M = 30 x 6 / 4 = 45 kN m, stress = 45 x 10^6 / 666 667 = 67.5 MPa > 60 MPa, so it fails. Required Z = 45 x 10^6 / 60 = 750 000 mm3, h^2 = 6 x 750 000 / 100 = 45 000, so h = 212 mm; use 215 mm stock.

Question 2: Two-stage Gear Train Ratios, Speed and Torque (16 marks)

A motor runs at 1 440 r/min and delivers 1.5 kW through a two-stage gear reducer. Stage 1 has a 20-tooth driver and a 60-tooth driven gear; stage 2 has a 20-tooth driver and an 80-tooth driven gear. Each stage is 95% efficient (about 90% overall).

# Question Answer and marking notes
5 Find the speed ratio of each stage and the overall ratio. Stage 1: 60 / 20 = 3. Stage 2: 80 / 20 = 4. Overall ratio = 3 x 4 = 12.
6 Find the speed of the intermediate shaft and of the output shaft. Intermediate shaft: 1 440 / 3 = 480 r/min. Output shaft: 1 440 / 12 = 120 r/min.
7 Find the motor output torque (N m). omega = 2 pi x 1 440 / 60 = 150.8 rad/s; T = 1 500 / 150.8 = 9.95 N m.
8 Find the output torque and output power, allowing for efficiency. Output torque = 9.95 x 12 x 0.90 = 107.4 N m; output power = 1 500 x 0.90 = 1 350 W. Lower speed with higher torque matches the reduction principle.

Question 3: Tensile Test, Ultimate Strength and Young Modulus (16 marks)

A cylindrical metal specimen of diameter 10 mm and gauge length 50 mm is tested in tension. It fractures at 25 kN, and within the elastic range a load of 12 kN stretches the gauge length by 0.045 mm.

# Question Answer and marking notes
9 Find the cross-sectional area of the specimen (mm2). A = pi x 10^2 / 4 = 78.5 mm2.
10 Find the ultimate tensile strength (MPa). Ultimate strength = 25 000 / 78.5 = 318 MPa.
11 Find the engineering stress (MPa) and strain at 12 kN. Stress = 12 000 / 78.5 = 153 MPa; strain = 0.045 / 50 = 9.0 x 10^-4.
12 Find Young modulus (GPa) and state what it means. E = 153 x 10^6 / 9.0 x 10^-4 = 1.70 x 10^11 Pa = 170 GPa. Young modulus measures stiffness in the elastic range: the larger the value, the smaller the strain for a given stress.

Question 4: Series Voltage Divider and Power Dissipation (16 marks)

A 12 V dc supply is connected in series with R1 = 220 ohm and R2 = 470 ohm. A LED with a forward voltage of 2.0 V may optionally be added in series.

# Question Answer and marking notes
13 Find the total resistance of the circuit. Series resistances add: 220 + 470 = 690 ohm.
14 Find the circuit current (mA). I = 12 / 690 = 0.0174 A = 17.4 mA.
15 Find the voltage across R2 (V). V2 = 0.01739 x 470 = 8.17 V, the divider ratio being 470 / 690.
16 Find the total resistor power without the LED; with the LED in series, find the new current and total resistor power. Without LED: P = 12 x 0.01739 = 0.209 W. With LED: I = (12 – 2.0) / 690 = 0.01449 A = 14.5 mA, and P = 0.01449^2 x 690 = 0.145 W.

Question 5: Product Cost, Contribution Margin and Break-even (16 marks)

A product has monthly fixed costs of HK$180 000, a unit variable cost of HK$45 and a selling price of HK$75. Monthly capacity is 8 000 units.

# Question Answer and marking notes
17 Find the unit contribution margin and the break-even quantity. Contribution = 75 – 45 = HK$30 per unit; break-even = 180 000 / 30 = 6 000 units.
18 How many units must be sold to earn HK$60 000 profit per month? Is it feasible? Q = (180 000 + 60 000) / 30 = 8 000 units, exactly at capacity: feasible but with no spare capacity.
19 If the price is cut to HK$70, find the new break-even quantity. New contribution = 70 – 45 = HK$25; break-even = 180 000 / 25 = 7 200 units, 1 200 more than before.
20 With price HK$70 and capacity 8 000 units, find the maximum profit and the margin of safety as a percentage of capacity. Maximum profit = 25 x 8 000 – 180 000 = HK$20 000; margin of safety = (8 000 – 7 200) / 8 000 = 10%, compared with 25% at a price of HK$75.

Question 6: Crank-slider Mechanism and Production Rate (16 marks)

In a crank-slider mechanism the crank radius is 50 mm and the connecting rod is 200 mm long. The crank turns at a constant 300 r/min and the slider feeds one workpiece on each complete stroke.

# Question Answer and marking notes
21 Find the angular velocity of the crank (rad/s). omega = 2 pi x 300 / 60 = 31.4 rad/s.
22 Find the linear speed of the crank pin (m/s) and the slider stroke (mm). v = 31.42 x 0.05 = 1.57 m/s; stroke = 2 x 50 = 100 mm.
23 Using v = omega r (1 + r / 2L), find the maximum slider speed (m/s). r / L = 0.25, so maximum speed = 1.571 x 1.125 = 1.77 m/s.
24 Find the maximum slider acceleration (m/s2) using a = omega^2 r (1 + r / L), and the number of workpieces fed per hour. Maximum acceleration = 31.42^2 x 0.05 x 1.25 = 61.7 m/s2; the crank turns 5 times a second, so 5 x 3 600 = 18 000 workpieces per hour.

Find a tutor — freeTutor Registration →

A TutorZone practice paper; original questions and passages, not publisher material.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →