IGCSE Chemistry — States of Matter and the Kinetic Particle Model: Lesson-Prep Guide (for tutors) | Heating-curve plateaus, melting and boiling points, diffusion
- 2026-11-17
Students can often say that temperature stays flat during melting, but cannot say where the energy goes; asked why ammonia travels further than hydrogen chloride, they answer that ammonia is lighter and stop there. This lesson explains the three states, the two plateaus and diffusion with one particle language, and checks understanding with two computed results: 15,500 J for 20 g of ice and a meeting point at 59.4 cm.
01 Prerequisites (3-minute check)
If any of these fails, fix it before the lesson starts.
| Skill | Quick check | Pass mark |
|---|---|---|
| Reading a thermometer | What state change happens at 0 °C and at 100 °C | Melting of ice, boiling of water |
| Meaning of specific heat capacity | Water or oil heats faster for the same mass and heater | Oil, because its specific heat capacity is lower |
| Relative molecular mass | Work out Mr for ammonia and hydrogen chloride | 17 and 36.5 |
02 Lesson flow (45 minutes)
| Time | Stage | Tutor does | Student does |
|---|---|---|---|
| 0-6 min | Diagnostic | Ask three questions: how the particles differ in the three states, where the energy goes on a plateau, why ammonia travels further | Students write answers without notes |
| 6-18 min | Act 1: three states differ in three things | Use one set of particles to compare arrangement, motion and forces | Students fill a comparison table and circle the key change |
| 18-32 min | Act 2: heating curve and two plateaus | Work through 20 g of ice in three stages: 420 J, 6,680 J, 8,400 J, total 15,500 J, so 155 s at 100 J per second | Students compute one stage and check the 43.1% share |
| 32-40 min | Act 3: diffusion and Mr | Use the square-root ratio 1.47 so ammonia travels 59.4 cm of a 100 cm tube | Students find the 40.6 cm for hydrogen chloride and check the ratio |
| 40-43 min | New context | Change the tube to 50 cm and ask where they meet | Answer orally: 29.7 cm from the ammonia end |
| 43-45 min | Exit check | Collect three questions and sort errors into particles, plateau or diffusion | Independent work |
03 Teaching script (read it out)
Scene 1: Act 1: the three states differ in only three things
Say it in one sentence: a change of state changes the distance and motion of particles, not their size.
Scene 2: Act 2: the plateau energy overcomes forces
Students should say: on a plateau the temperature is constant because energy becomes latent heat, not extra kinetic energy.
Scene 3: Act 3: lighter molecules diffuse faster
Students should say: the heavier molecule moves slower, so the white ring forms nearer the hydrogen chloride end.
04 Question types and worked steps
| Type | Example | Steps | Answer |
|---|---|---|---|
| Particle description | One sentence for arrangement, one for motion, one for forces | ||
| Heating-curve calculation | Energy per stage (mass times specific heat capacity times temperature change, or mass times latent heat), then divide by power | ||
| Plateau explanation | Energy overcomes forces between particles, kinetic energy unchanged, so temperature is constant | ||
| Diffusion comparison | Square-root ratio of relative molecular masses, then share the tube length in that ratio | ||
| Naming state changes | Melting, freezing, boiling, condensing and subliming, each with a direction | ||
| Comparing slopes | A substance with a larger specific heat capacity has a flatter slope | ||
| Experimental error | Heat loss, uneven heating and thermometer lag are the three sources to name |
05 Independent practice (3 questions)
| Question | Answer | What to watch |
|---|---|---|
| How much energy heats 20 g of ice from -10 °C to 0 °C? | 420 J (20 times 2.1 times 10) | Missing the 10 °C temperature change |
| How much energy melts all of that ice at 0 °C? | 6,680 J (20 times 334) | Using specific heat capacity instead of latent heat |
| What is the total energy for the three stages? | 15,500 J | Checking that 420 plus 6,680 plus 8,400 adds up |
| At 100 J per second, how long does the whole process take? | 155 s | Answering 1,550 s after dividing by 10 |
| What is the diffusion rate ratio for ammonia and hydrogen chloride? | About 1.47 (square root of 36.5 divided by 17) | Forgetting the square root |
| How far does ammonia travel in a 100 cm tube before they meet? | 59.4 cm | Swapping 59.4 and 40.6 |
06 Common mistakes and what to say
| Mistake | Student writes | Say this |
|---|---|---|
| Particles grow on heating | The particles get bigger, so the substance expands | Heating increases the distance between particles; the particles themselves stay almost the same size. |
| Plateau means heating stopped | The curve is flat, so no more energy is going in | Energy is still going in, but all of it overcomes forces between particles, so temperature does not rise. |
| Comparing masses directly for diffusion | Hydrogen chloride is 36.5 and ammonia is 17, so it is more than twice as slow | Take square roots: 36.5 divided by 17, then square root, gives about 1.47. |
| Mixing up latent heat and specific heat capacity | Writing 20 times 4.2 times 100 for the melting stage | Melting has no temperature change; use the 334 J per gram latent heat. |
07 Homework (paper, section and question numbers)
- IGCSE Chemistry chapter index (states of matter and atomic structure) — Questions 1-4
- IGCSE lesson-prep overview (three subjects side by side) — Questions 1-6
08 Exit check (last 5 minutes)
| Question | Answer | Decision |
|---|---|---|
| Where does the energy go on the plateau? | Into overcoming forces between particles, so kinetic energy and temperature stay constant | Re-teach Act 2 |
| How much energy melts 20 g of ice? | 6,680 J | Re-teach the latent heat step |
| Where do ammonia and hydrogen chloride meet in a 100 cm tube? | 59.4 cm from the ammonia end | Re-teach the square-root ratio in Act 3 |
09 Tutor FAQ
Why does the temperature stay at 0 °C while ice melts?
The energy supplied breaks the regular arrangement of particles, so it does not raise their kinetic energy. Only after melting is complete does the energy raise kinetic energy and the temperature again.
How is diffusion different from convection?
Diffusion comes from the random motion of particles and needs no draught; convection is bulk movement of a fluid driven by density differences. An exam answer about smelling a gas should refer to random particle motion, not wind.
Should heat loss be included in heating-time calculations?
Ideal questions ignore it. If the question gives an efficiency, such as 80% of the energy being absorbed, divide the calculated energy by 0.8 before dividing by the power. Skipping that step is the most common lost mark.
Find a tutor — freeTutor Registration →
A TutorZone lesson-prep guide. Written by the TutorZone team; questions and lesson flow are original and are not taken from any school or publisher material.



