S3 Physics Heat and Energy Transfer Practice 3 (Challenge)
- 2026-11-21
S3 Physics Heat and Energy Transfer Practice 3 (Challenge)
Ten items cover latent heat of fusion, two-stage heating, efficiency chains and heat-loss rates, applied to solar panels and vacuum flasks.
Latent heat and multi-stage energy chains List the stages first, apply Q = mcΔT or Q = mL to each, and add only at the end.
01 Paper details (check answers afterwards)
| Item | Detail |
|---|---|
| Questions | 10 |
| Suggested time | 25 |
| Difficulty mix | Foundation 4 · Intermediate 2 · Challenge 2 · Error redo 2 |
| Chapter | Chapter: S3 Physics: heat and energy transfer |
| Level | Challenge |
02 Questions (10 items)
- FoundationHow much energy melts 2 kg of ice at 0 °C into water at 0 °C? (specific latent heat of fusion 334 000 J/kg)
- FoundationHow much energy turns 0.5 kg of ice at −10 °C into water at 0 °C? (ice 2100 J/(kg·°C), latent heat of fusion 334 000 J/kg)
- FoundationA 2000 W heater is 80 % efficient. How long does it take to raise 2 kg of water by 40 °C?
- FoundationAn electric water heater uses 3 kWh of electricity while the water absorbs 8.64 × 10⁶ J. Find the efficiency.
- Intermediate0.3 kg of water at 90 °C is mixed with 0.2 kg at 20 °C, with no heat loss. Find the final temperature.
- IntermediateA 5 kg water tank cools from 60 °C to 55 °C in 30 minutes. Find the average rate of heat loss.
- ChallengeA solar panel receives 5 kWh per square metre per day. With 6 m² at 18 % efficiency, how much electrical energy is produced daily?
- ChallengeA vacuum flask uses a vacuum layer, a silvered wall and a sealed lid. Which mode of heat transfer does each address?
- Error redoHeaters A (1000 W) and B (1500 W) heat the same kettle by the same rise. What is the ratio of their times?
- Error redoA 500 W heater is 70 % efficient. How long does it take to boil 1 kg of water from 20 °C to 100 °C?
03 Answers and one-line notes
| # | Answer | One-line note |
|---|---|---|
| 1 | 668000 J, that is 668 kJ. | Temperature stays at 0 °C, so use Q = mL rather than mcΔT. |
| 2 | 177500 J (warming 10500 J plus melting 167000 J). | Two stages: warm the ice, then supply latent heat; add both amounts. |
| 3 | About 210 s. | Useful power is 2000 × 0.8 = 1600 W; divide 336 000 J by that. |
| 4 | Input is 10800000 J, so efficiency = 80 % (that is 80 %). | Unify units first: 1 kWh = 3.6 × 10⁶ J, then useful ÷ input. |
| 5 | 62 °C. | Heat lost equals heat gained, so (0.3 × 90 + 0.2 × 20) ÷ 0.5. |
| 6 | About 58.3 W. | Energy released is 105 000 J over 1800 s. |
| 7 | 5.4 kWh. | 5 × 6 × 0.18: incident energy × area × efficiency. |
| 8 | The vacuum stops conduction and convection, the silvered wall reflects radiation, and the lid blocks convection of hot air and reduces evaporation loss. | Each mode of transfer has to be handled separately. |
| 9 | A : B = 3 : 2, so A takes 1.5 times as long as B. | For equal energy, time is inversely proportional to power: 1000 : 1500 gives the inverse 2 : 3. |
| 10 | About 960 s (16 min). | Useful power is 350 W and the energy needed is 336 000 J. |
04 What to do after marking
- After marking, redo only the wrong items and write down which step went wrong (formula, unit, or misread number).
- Repeat the same item two days later; move to the next paper only when both attempts are correct.
- Parents only need the answer and note columns; there is no need to explain every item.
Download the full ten-item paper as a PDF, answers and notes included.Tutor Registration →
Questions and answers are written originally by the TutorZone team and are not taken from any school, publisher or examination authority paper. Every value is checked by computer.



