S3 Science: Forces and Simple Machines – Paper 3 (Challenge, 10 items)
- 2026-11-16
← Back to the Secondary Science chapter index
S3 Science: Forces and Simple Machines – Paper 3 (Challenge, 10 items)
Handle asymmetric levers, moment balance on a carried plank, multi-stage gear trains and pump power as combined applications.
Focus Balance with unequal arms, a ramp at 75 percent efficiency, advantage times efficiency, the 20-40-10 gear train, taking one end as the pivot to find a support force, power = mgh / t, ramp length from the advantage, teeth from a speed ratio, a 5 to 1 arm ratio, force saved but energy not saved.
01 Paper details (check answers afterwards)
| Item | Detail |
|---|---|
| Questions | 10 |
| Suggested time | 25 |
| Difficulty mix | Foundation 4 · Intermediate 3 · Challenge 2 · Error redo 1 |
| Chapter | Chapter: S3 Science: Forces and Simple Machines |
| Level | Challenge, 10 items, about 25 minutes |
02 Questions (10 items)
- FoundationA light 2.0 m rod is pivoted 1.2 m from its left end. What weight at the right end balances 18 N at the left end?
- FoundationA 300 N load is pushed 5 m up a ramp to 1.5 m with an effort of 120 N. What is the efficiency?
- FoundationA pulley system with mechanical advantage 5 runs at 70% efficiency. What effort lifts 350 N?
- Foundation20 teeth drive 40 teeth, then 40 teeth drive 10 teeth. If the 20-tooth gear turns at 300 rpm, what is the final speed?
- IntermediateA 2.4 m plank weighs 240 N with its centre in the middle and is carried at both ends. What does each end take, and what does end A take if 100 N sits 0.6 m from A?
- IntermediateA pump raises 600 kg of water through 5 m every minute (g = 10 N/kg). What is its power?
- IntermediateA ramp has mechanical advantage 4 and must raise a load 0.8 m. How long is the ramp?
- ChallengeAn output must turn four times faster than a 48-tooth input. How many teeth should the output gear have?
- ChallengeA lever must multiply force five times with a short arm of 15 cm. How long is the long arm?
- Error redoA 5 m ramp rises 1 m and a 20 N push moves the load along it. How much work is done, compared with lifting 100 N by 1 m directly?
03 Answers and one-line notes
| # | Answer | One-line note |
|---|---|---|
| 1 | 27 N. | The left arm is 1.2 m and the right arm 0.8 m, so 18 x 1.2 = W x 0.8 and W = 21.6 / 0.8 = 27 N. |
| 2 | 75%. | Useful work is 300 x 1.5 = 450 J and input work is 120 x 5 = 600 J, so 450 / 600 = 75%. |
| 3 | 100 N. | Actual mechanical advantage = 5 x 0.7 = 3.5, so 350 N / 3.5 = 100 N. |
| 4 | 600 rpm. | 20 to 40 halves the speed to 150 rpm, then 40 to 10 multiplies it by four to 600 rpm. |
| 5 | 120 N each at first; then A carries 195 N. | Taking moments about B: A x 2.4 = 240 x 1.2 + 100 x 1.8 = 468, so A = 195 N and B = 145 N. |
| 6 | 500 W. | Work per minute is 600 x 10 x 5 = 30 000 J, so 30 000 / 60 s = 500 W. |
| 7 | 3.2 m. | Length = mechanical advantage x height = 4 x 0.8 m = 3.2 m. |
| 8 | 12 teeth. | 48 / 4 = 12: fewer teeth means a faster rotation. |
| 9 | 75 cm. | Equal moments give F x L = 5F x 15, so the arms are in the ratio 5 to 1 and L = 15 x 5 = 75 cm. |
| 10 | 100 J either way. | The ramp gives five times the force over five times the distance: 20 x 5 = 100 J, the same as 100 N x 1 m, so force is saved but energy is not. |
04 What to do after marking
- After marking, redo only the wrong items and write down which step went wrong (formula, unit, or misread number).
- Repeat the same item two days later; move to the next paper only when both attempts are correct.
- Parents only need the answer and note columns; there is no need to explain every item.
After finishing, pick one ramp question and solve it once through efficiency and once through work, then confirm the answers agree.Tutor Registration →
Questions and answers are written originally by the TutorZone team and are not taken from any school, publisher or examination authority paper. Every value is checked by computer.



