/en-tutor-prep-s6-physics-interference-diffraction-grating-practice-2/
/en-tutor-prep-s6-physics-interference-diffraction-grating-practice-2/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

S6 Physics | Interference, diffraction and gratings – advanced paper (10 questions with answers)

S6 Physics | Interference, diffraction and gratings – advanced paper (10 questions with answers)

  • 2026-11-16

S6 Physics | Interference, diffraction and gratings – advanced paper (10 questions with answers)

Paper two uses both formulas backwards: wavelength from fringe spacing, slit spacing from line density, then angles and maximum order from d sin θ = nλ.

Advanced order of working: convert units, rearrange, then take the inverse sine For interference and diffraction items, first put every length in metres, write down what is given and what is asked, and only then substitute. Once sin θ is found, take the inverse sine. The order is always a whole number, limited by d ÷ λ rounded down.

01 Paper details (check answers afterwards)

Item Detail
Questions 10
Suggested time 25
Difficulty mix Intermediate 7 · Challenge 2 · Error redo 1
Chapter Chapter: S6 Physics | Interference, diffraction and gratings
Level Level: advanced items on reverse wavelength, diffraction angles and unit conversion

02 Questions (10 items)

  1. IntermediateIn a double-slit experiment the slit spacing is 0.25 mm, the screen is 1.5 m away and the wavelength is 500 nm. Find the fringe spacing.
  2. IntermediateThe same set-up (d = 0.25 mm, L = 1.5 m) now uses 750 nm red light. What is the new fringe spacing?
  3. IntermediateThe slit spacing is halved to 0.125 mm while the screen distance and wavelength stay at 1.5 m and 500 nm. Find the new spacing.
  4. IntermediateA double-slit set-up has d = 0.30 mm and L = 1.2 m; the measured fringe spacing is 2.4 mm. Find the wavelength.
  5. IntermediateA grating has 300 lines per millimetre. Find the slit spacing d in micrometres.
  6. IntermediateThe same grating (d = 3.33 micrometres) is lit normally by 589 nm sodium light. Find the first-order diffraction angle.
  7. IntermediateFor the same grating and the same 589 nm light, find the second-order diffraction angle.
  8. ChallengeHow many orders at most are visible with this grating (d = 3.33 micrometres) under 589 nm light?
  9. ChallengeAnother grating has 500 lines per millimetre. With 550 nm green light at normal incidence, find the first-order angle.
  10. Error redoA student answers 3.33 orders for the maximum order of a grating with d = 2.0 micrometres at 600 nm. What is correct?

03 Answers and one-line notes

# Answer One-line note
1 y = λL ÷ d = (500 × 10⁻⁹ × 1.5) ÷ (0.25 × 10⁻³) = 3.0 × 10⁻³ m, that is 3.0 mm. Convert all three lengths to metres first: nm times 10⁻⁹, mm times 10⁻³, then change back to mm at the end.
2 y = (750 × 10⁻⁹ × 1.5) ÷ (0.25 × 10⁻³) = 4.5 × 10⁻³ m, that is 4.5 mm. Fringe spacing is proportional to wavelength, so going from 500 nm to 750 nm scales it by 1.5.
3 y = (500 × 10⁻⁹ × 1.5) ÷ (0.125 × 10⁻³) = 6.0 × 10⁻³ m, that is 6.0 mm. Spacing is inversely proportional to slit spacing, so halving d doubles the fringe width.
4 λ = y d ÷ L = (2.4 × 10⁻³ × 0.30 × 10⁻³) ÷ 1.2 = 6.0 × 10⁻⁷ m, that is 600 nm. Rearranging y = λL ÷ d gives this form; do not divide by L twice.
5 d = 1 mm ÷ 300 = 3.33 × 10⁻³ mm = 3.33 × 10⁻⁶ m, about 3.3 micrometres. Lines per millimetre means d = 1/n mm, never d = n mm.
6 sin θ = λ ÷ d = (589 × 10⁻⁹) ÷ (3.33 × 10⁻⁶) = 0.177, so θ is about 10.2 degrees. Work out sin θ first and then take the inverse sine; never start by slotting an angle into the equation.
7 sin θ = 2λ ÷ d = (2 × 589 × 10⁻⁹) ÷ (3.33 × 10⁻⁶) = 0.353, so θ is about 20.7 degrees. The order n multiplies the numerator only; angles are not proportional to the order.
8 d ÷ λ = 3.33 × 10⁻⁶ ÷ 589 × 10⁻⁹ = 5.66, so the fifth order is the highest visible one. The order must be a whole number, and the limit comes from n ≤ d ÷ λ.
9 d = 1 ÷ 500 mm = 2.0 micrometres; sin θ = 550 × 10⁻⁹ ÷ 2.0 × 10⁻⁶ = 0.275, so θ is about 16.0 degrees. More lines per millimetre means a finer d, which gives a larger angle for the same wavelength.
10 n ≤ d ÷ λ = 2.0 × 10⁻⁶ ÷ 600 × 10⁻⁹ = 3.33, and orders are whole numbers, so the third is the highest. The 3.33 is only a ratio limit, not an order; always round down to a whole order.

04 What to do after marking

  • After marking, redo only the wrong items and write down which step went wrong (formula, unit, or misread number).
  • Repeat the same item two days later; move to the next paper only when both attempts are correct.
  • Parents only need the answer and note columns; there is no need to explain every item.

When marking, check units as well: with d and λ both in metres the angle comes out in degrees.Tutor Registration →

Questions and answers are written originally by the TutorZone team and are not taken from any school, publisher or examination authority paper. Every value is checked by computer.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →