S6 Physics: Interference, Diffraction and Gratings (10 Retry Items)
- 2026-11-16
S6 Physics: Interference, Diffraction and Gratings (10 Retry Items)
Ten retry items on the three slips that cost most marks: unit conversion, sine versus angle, and whole-number orders. Expect 4.0 mm rather than 4.0 m, 17.5 degrees for a sine of 0.300, the third order from 3.33, 2.0 micrometres from 500 lines per millimetre, and red bent most in white light.
Fix only the differences A retry paper adds no new content; it corrects the units, sine values and orders that went wrong before. Write your original answer first, then compare and note only the difference.
01 Paper details (check answers afterwards)
| Item | Detail |
|---|---|
| Questions | 10 |
| Suggested time | 25 |
| Difficulty mix | Error redo 10 |
| Chapter | Chapter: S6 Physics: Interference, Diffraction and Gratings |
| Level | S6 Physics |
02 Questions (10 items)
- Error redoRetry 1: a student takes the slit separation of 0.30 mm as 0.30 m and obtains a fringe spacing of 4.0 m. With wavelength 600 nm and screen distance 2.0 m, what is the correct spacing, and by what factor is his answer too large?
- Error redoRetry 2: with adjacent fringes 1.5 mm apart, a student says the third bright fringe is 1.5 mm from the centre. How far is it really, and what did he confuse?
- Error redoRetry 3: a grating has 500 lines per millimetre and a student answers that the grating constant is 500 mm. What is d, in metres and in micrometres?
- Error redoRetry 4: the grating equation gives sin theta equal to 0.300 and a student answers theta equals 0.300 degrees. What is the correct angle, and which step went wrong?
- Error redoRetry 5: with d equal to 2.0 micrometres and wavelength 600 nm, a student answers that the highest visible order is 3.33. What is the highest order, and why?
- Error redoRetry 6: an experiment gives fringes 2.4 mm apart, a screen 1.5 m away and slits 0.25 mm apart, and a student copies 600 nm from an earlier paper. What is the wavelength?
- Error redoRetry 7: the double-slit set is immersed in water of refractive index 1.33 and a student says neither wavelength nor spacing changes. What does the wavelength become, and what happens to the 4.0 mm spacing?
- Error redoRetry 8: a single slit 0.10 mm wide, a screen 1.0 m away and light of 500 nm give a central maximum of what full width, and what happens if the slit width is halved?
- Error redoRetry 9: a grating with 300 lines per millimetre is used with light of 589 nm, and a student gives 0.177 and 0.353 degrees for the first two orders. What are the correct angles?
- Error redoRetry 10: white light falls normally on a grating with d equal to 2.0 micrometres and a student claims violet is bent most in the first order. What are the angles for red at 700 nm and violet at 400 nm?
03 Answers and one-line notes
| # | Answer | One-line note |
|---|---|---|
| 1 | The correct spacing is 4.0 mm, from wavelength times distance over slit separation; his answer is 1 000 times too large. | A millimetre is ten to the minus three metres; skipping that step shifts the answer by three orders of magnitude. |
| 2 | It is 4.5 mm from the centre, three spacings; he treated the third fringe as the first order. | The n-th bright fringe sits n spacings from the centre, so the order has to be multiplied in. |
| 3 | d is 2.0 micrometres, that is 2.0 times ten to the minus six metres; 500 lines per millimetre means neighbouring lines are microns apart. | Line density and spacing are reciprocals: N lines per millimetre give a spacing of 1/N millimetres. |
| 4 | Theta is about 17.5 degrees; the sine value still has to be inverted and converted to degrees. | A sine of 0.300 corresponds to 17.5 degrees; quoting the sine as the angle is the commonest slip. |
| 5 | It is the third order, since d over the wavelength is 3.33 and the fourth order would need a sine above one. | Divide d by the wavelength and round down; the fractional part is simply short of the next order. |
| 6 | It is 4.0 times ten to the minus seven metres, that is 400 nm. | The relation links spacing, slit separation and screen distance, so the numbers of this paper must be used. |
| 7 | The wavelength falls to about 451 nm and the spacing shrinks in proportion to about 3.0 mm. | Frequency is fixed by the source; speed and wavelength both fall, and the spacing scales with wavelength. |
| 8 | Half-width 5.0 mm so full width 10.0 mm, doubling to 20.0 mm when the slit is halved. | The central maximum widens as the slit narrows; its width is inversely proportional to slit width. |
| 9 | d is 3.33 micrometres, giving 10.2 degrees for the first order and 20.7 degrees for the second. | The sine values must be inverted, and the line density has to be turned into a spacing first. |
| 10 | Red gives 20.5 degrees and violet 11.5 degrees, a difference of 9.0 degrees, so red is bent most and only the central maximum stays white. | Longer wavelength means a larger diffraction angle, so each order spreads from violet inwards to red outwards. |
04 What to do after marking
- After marking, redo only the wrong items and write down which step went wrong (formula, unit, or misread number).
- Repeat the same item two days later; move to the next paper only when both attempts are correct.
- Parents only need the answer and note columns; there is no need to explain every item.
Book an S6 Physics tutorTutor Registration →
Questions and answers are written originally by the TutorZone team and are not taken from any school, publisher or examination authority paper. Every value is checked by computer.



