/en-tutor-prep-s3-ict-robotics-automation-practice-1/
/en-tutor-prep-s3-ict-robotics-automation-practice-1/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

Paper 1: Robotics basics: sensors, levels and motion

Paper 1: Robotics basics: sensors, levels and motion

  • 2026-11-21

Paper 1: Robotics basics: sensors, levels and motion

Chapter practice with ten items, answers and a one-line note for each, about 25 minutes.

Paper 1 Ten items on this chapter with answers for immediate marking.

01 Paper details (check answers afterwards)

Item Detail
Questions 10
Suggested time 25
Difficulty mix Foundation 4 · Intermediate 2 · Challenge 2 · Error redo 2
Chapter Chapter: Robotics and automation
Level Basic

02 Questions (10 items)

  1. FoundationA 10-bit analogue-to-digital converter (ADC) can tell how many input levels apart?
  2. FoundationWith a 5 V reference, how many volts does each level of a 10-bit ADC represent (four decimal places)?
  3. FoundationHow many levels does an 8-bit ADC have?
  4. FoundationThe controller updates its output every 20 milliseconds. What is the control frequency in hertz?
  5. IntermediateWhat is the main difference between closed-loop and open-loop control?
  6. IntermediateA line-following robot uses a light-dependent resistor to detect black and white ground. Which kind of component is it?
  7. ChallengeA robot arm has 6 joints that can each move independently. How many degrees of freedom does it have?
  8. ChallengeA motor is rated at 3,000 rpm. How many revolutions per second is that?
  9. Error redoA wheel has a diameter of 10 cm (take pi as 3.14). How far does the robot travel in 100 wheel turns?
  10. Error redoA sonar sensor hears the echo 0.02 seconds after sending a pulse. Sound travels at 340 metres per second. How far away is the obstacle?

03 Answers and one-line notes

# Answer One-line note
1 1,024 A converter with n bits has 2 to the power n levels, so 10 bits gives 1,024 levels.
2 0.0049 V 5 V spread over 1,024 levels gives about 0.0049 V per level, that is 4.9 millivolts.
3 256 2 to the power 8 is 256, and every extra bit doubles the number of levels.
4 50 Hz One second holds 1,000 milliseconds, so 1,000 divided by 20 gives 50 updates each second.
5 Closed-loop control measures the actual output and compares it with the target; open-loop control does not measure the output. Only feedback allows error correction, so closed-loop control stays accurate when the load changes.
6 A sensor, that is an input device. It turns light intensity into an electrical signal for the controller, so it sits on the input side.
7 6 Each independently driven joint adds one degree of freedom, so 6 joints give 6.
8 50 rpm means revolutions per minute, so 3,000 divided by 60 gives 50 revolutions each second.
9 31.4 m One turn covers 3.14 times 10, which is 31.4 cm, so 100 turns cover 3,140 cm, that is 31.4 metres.
10 3.4 m The sound makes a return trip, so divide by 2: 340 times 0.02 divided by 2 gives 3.4 metres.

04 What to do after marking

  • After marking, redo only the wrong items and write down which step went wrong (formula, unit, or misread number).
  • Repeat the same item two days later; move to the next paper only when both attempts are correct.
  • Parents only need the answer and note columns; there is no need to explain every item.

Want the whole chapter? See all four difficulty papers on the chapter page.Tutor Registration →

Questions and answers are written originally by the TutorZone team and are not taken from any school, publisher or examination authority paper. Every value is checked by computer.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →