Paper 2: Encoders, PID and drive trains
- 2026-11-21
Paper 2: Encoders, PID and drive trains
Chapter practice with ten items, answers and a one-line note for each, about 25 minutes.
Paper 2 Ten items on this chapter with answers for immediate marking.
01 Paper details (check answers afterwards)
| Item | Detail |
|---|---|
| Questions | 10 |
| Suggested time | 25 |
| Difficulty mix | Foundation 4 · Intermediate 2 · Challenge 2 · Error redo 2 |
| Chapter | Chapter: Robotics and automation |
| Level | Advanced |
02 Questions (10 items)
- FoundationHow many levels does a 12-bit ADC have?
- FoundationA 12-bit ADC uses a 3.3 V reference. How many millivolts does each level represent (three decimal places)?
- FoundationAn encoder gives 1,000 pulses per turn and the controller counts both edges of both channels, so every pulse counts four times. How many counts per turn, and how many over 2.5 turns?
- FoundationIf the control period is shortened to 5 milliseconds, what is the new control frequency in hertz?
- IntermediateA PID controller has Kp 2, Ki 0.5 and Kd 0.1. The error is 3, the accumulated error is 4 and the rate of change is 5. What is the output?
- IntermediateA motor running at 6,000 rpm drives an output shaft through a 20 to 1 gearbox. What is the output speed in rpm and in turns per second?
- ChallengeThe target position is 500 mm and the arm stops at 500.4 mm. The tolerance is 2 mm. Does it pass, and what is the deviation?
- ChallengeA signal has a highest frequency of 25 Hz. According to the sampling theorem, what is the minimum sampling rate?
- Error redoA joint moves at 90 degrees per second. How long does it take to go from 0 to 270 degrees?
- Error redoA robot battery is rated 5,000 mAh and the robot draws 2,000 mA on average. How many hours can it run?
03 Answers and one-line notes
| # | Answer | One-line note |
|---|---|---|
| 1 | 4,096 | 2 to the power 12 is 4,096, which is four times the count of a 10-bit converter. |
| 2 | 0.806 millivolts | 3.3 divided by 4,096 gives 0.0008057 V, which is 0.806 millivolts. |
| 3 | 4,000 per turn and 10,000 in total. | Four times 1,000 gives 4,000 counts per turn, and times 2.5 turns gives 10,000 counts. |
| 4 | 200 Hz | 1,000 divided by 5 gives 200, and a shorter period means more corrections every second. |
| 5 | 8.5 | 2 times 3 is 6, 0.5 times 4 is 2 and 0.1 times 5 is 0.5, so the three parts add up to 8.5. |
| 6 | 300 rpm and 5.0 turns per second. | The gearbox divides speed by 20, so 6,000 becomes 300 rpm, which is 5.0 turns each second. |
| 7 | It passes, with a deviation of 0.4 mm. | The difference between 500.4 and 500 is 0.4 mm, which is inside the 2 mm tolerance. |
| 8 | 50 Hz | The sampling rate must exceed twice the highest frequency, and 25 times 2 is 50. |
| 9 | 3.0 seconds | 270 divided by 90 gives 3.0, so the move takes 3.0 seconds. |
| 10 | 2.5 hours | Capacity divided by current gives 5,000 over 2,000, which is 2.5 hours. |
04 What to do after marking
- After marking, redo only the wrong items and write down which step went wrong (formula, unit, or misread number).
- Repeat the same item two days later; move to the next paper only when both attempts are correct.
- Parents only need the answer and note columns; there is no need to explain every item.
Want the whole chapter? See all four difficulty papers on the chapter page.Tutor Registration →
Questions and answers are written originally by the TutorZone team and are not taken from any school, publisher or examination authority paper. Every value is checked by computer.



