Paper 3: Multi-step robotics calculations
- 2026-11-21
Paper 3: Multi-step robotics calculations
Chapter practice with ten items, answers and a one-line note for each, about 25 minutes.
Paper 3 Ten items on this chapter with answers for immediate marking.
01 Paper details (check answers afterwards)
| Item | Detail |
|---|---|
| Questions | 10 |
| Suggested time | 25 |
| Difficulty mix | Foundation 4 · Intermediate 2 · Challenge 2 · Error redo 2 |
| Chapter | Chapter: Robotics and automation |
| Level | Challenge |
02 Questions (10 items)
- FoundationHow many levels does a 16-bit ADC have?
- FoundationA 16-bit ADC uses a 5 V reference. How many microvolts does each level represent (one decimal place)?
- FoundationAn encoder gives 2,000 pulses per turn. With four-times counting, how many counts per turn, and what angle does one count represent (four decimal places)?
- FoundationA wheel has a diameter of 20 cm (take pi as 3.14159) and the encoder counts 500 times per turn. How many millimetres does one count represent (three decimal places)?
- IntermediateProportional control with Kp equal to 3 gives an output of 12 at 4 mm error and 3 at 1 mm error. What does this show?
- IntermediateA robot accelerates from rest at 1 metre per second squared up to 0.5 metres per second. How long does that take, and how far does it travel while accelerating?
- ChallengeA gripper holds a 10 kg load whose centre of mass is 0.4 m from the joint. Taking gravity as 9.8, what torque does the joint need (one decimal place)?
- ChallengeA sensor signal contains a 60 Hz component but the controller samples at only 100 Hz. What goes wrong?
- Error redoThe controller sends 8 bytes to the driver every cycle at 100 Hz. How many bytes per second is that?
- Error redoWhich kind of circuit should an emergency stop button be wired into? Can software alone stop the motor?
03 Answers and one-line notes
| # | Answer | One-line note |
|---|---|---|
| 1 | 65,536 | 2 to the power 16 is 65,536, doubling once for every added bit. |
| 2 | 76.3 microvolts | 5 divided by 65,536 gives 7.629e-05 V, which is about 76.3 microvolts per level. |
| 3 | 8,000 counts per turn and 0.045 degrees per count. | 2,000 times 4 is 8,000, and 360 degrees divided by 8,000 gives 0.045 degrees for each count. |
| 4 | 1.257 mm | One turn covers 3.14159 times 20, which is 62.8318 cm, so one count covers 0.125664 cm, that is 1.257 mm. |
| 5 | The output is proportional to the error, so a smaller error gives a smaller output and proportional action alone cannot remove steady-state error. | The proportional term only acts while an error remains, so an integral term is needed to drive the steady-state error to zero. |
| 6 | 0.5 seconds and 0.125 metres. | Time is 0.5 divided by 1, which is 0.5 seconds; distance is one half times acceleration times time squared, giving 0.125 metres. |
| 7 | 39.2 newton metres | Torque is force times lever arm: 10 times 9.8 is 98 N, and times 0.4 m gives 39.2 newton metres. |
| 8 | The sampling rate is below 120 Hz, so aliasing occurs and the high-frequency part is read as a lower frequency. | The sampling theorem requires more than twice the highest frequency, otherwise the original signal cannot be reconstructed. |
| 9 | 800 bytes | 8 times 100 gives 800, so 800 bytes travel every second. |
| 10 | It must be wired into a hardware safety circuit that cuts the power directly; software alone is not acceptable. | Software can crash or lose communication, so only a hard-wired break guarantees an immediate stop. |
04 What to do after marking
- After marking, redo only the wrong items and write down which step went wrong (formula, unit, or misread number).
- Repeat the same item two days later; move to the next paper only when both attempts are correct.
- Parents only need the answer and note columns; there is no need to explain every item.
Want the whole chapter? See all four difficulty papers on the chapter page.Tutor Registration →
Questions and answers are written originally by the TutorZone team and are not taken from any school, publisher or examination authority paper. Every value is checked by computer.



