/en-tutor-prep-s3-ict-robotics-automation-practice-4/
/en-tutor-prep-s3-ict-robotics-automation-practice-4/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

Paper 4: Common misconceptions corrected

Paper 4: Common misconceptions corrected

  • 2026-11-21

Paper 4: Common misconceptions corrected

Chapter practice with ten items, answers and a one-line note for each, about 25 minutes.

Paper 4 Ten items on this chapter with answers for immediate marking.

01 Paper details (check answers afterwards)

Item Detail
Questions 10
Suggested time 25
Difficulty mix Foundation 4 · Intermediate 2 · Challenge 2 · Error redo 2
Chapter Chapter: Robotics and automation
Level Retry

02 Questions (10 items)

  1. FoundationA student claims an 8-bit ADC has only 8 levels. What is the correct number?
  2. FoundationFor a 5 V, 8-bit ADC a student divides 5 by 8 and gets 0.625 V. What is the correct value (four decimal places)?
  3. FoundationA student says open-loop control can also correct errors automatically. Is that right?
  4. FoundationAn encoder gives 1,000 pulses per turn. A student says each pulse equals 1 degree. What is the correct angle (two decimal places)?
  5. IntermediateA 600 rpm motor drives through a 20 to 1 gearbox and a student calculates 12,000 rpm. What is the correct output speed?
  6. IntermediateA signal reaches 25 Hz and a student samples at 30 Hz, thinking that is enough. What is the correct minimum rate in hertz?
  7. ChallengeA sonar echo returns after 0.02 seconds and a student multiplies by 340 to get 6.8 metres. What is the correct distance?
  8. ChallengeA 5,000 mAh battery supplies 2,000 mA and a student answers 5,000 hours. What is the correct run time?
  9. Error redoA student thinks degrees of freedom equal the number of motors. How many degrees of freedom does an arm with 6 independently driven joints have?
  10. Error redoA student believes a larger proportional gain Kp is always better. What is wrong with that?

03 Answers and one-line notes

# Answer One-line note
1 256 levels The bit count is the exponent, not the number of levels, and 2 to the power 8 is 256.
2 0.0195 V Divide by the number of levels, 256, not by the bit count, so 5 over 256 gives 0.0195 V.
3 No. Open-loop control has no feedback and never measures the output, so it cannot correct errors. Only closed-loop control compares a measurement with the target, and only it can correct errors automatically.
4 0.36 degrees 360 degrees shared among 1,000 pulses gives 0.36 degrees for each pulse.
5 30.0 rpm A gearbox reduces speed rather than raising it, so 600 divided by 20 gives 30.0 rpm.
6 50 Hz The rate must be above 50 Hz, so 30 Hz is too low and produces aliasing.
7 3.4 m The echo covers the trip out and back, so divide by 2: 6.8 over 2 gives 3.4 metres.
8 2.5 hours Milliamp hours is a charge unit, so divide by the current: 5,000 over 2,000 gives 2.5 hours.
9 6 Degrees of freedom count independent directions of motion, and 6 independently driven joints give 6.
10 Too much gain causes oscillation or instability, so it must be tuned together with damping, sampling rate and mechanical limits. More gain gives a faster response, but too much makes the system overshoot repeatedly and lose stability.

04 What to do after marking

  • After marking, redo only the wrong items and write down which step went wrong (formula, unit, or misread number).
  • Repeat the same item two days later; move to the next paper only when both attempts are correct.
  • Parents only need the answer and note columns; there is no need to explain every item.

Want the whole chapter? See all four difficulty papers on the chapter page.Tutor Registration →

Questions and answers are written originally by the TutorZone team and are not taken from any school, publisher or examination authority paper. Every value is checked by computer.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →