/en-tutor-prep-s3-physics-magnetism-electromagnetism/
/en-tutor-prep-s3-physics-magnetism-electromagnetism/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

S3 Physics — Magnetism and Electromagnetism Prep Guide (for tutors): F=BIL gives 0.20 N, 500 to 50 turns gives 22 V, motor efficiency 75 percent

S3 Physics — Magnetism and Electromagnetism Prep Guide (for tutors): F=BIL gives 0.20 N, 500 to 50 turns gives 22 V, motor efficiency 75 percent

  • 2026-11-18

Students draw field lines as arrows that may cross, and treat a transformer as a machine that multiplies power. This lesson pins force, field and power to one set of numbers: 0.40 T, 2.5 A and 0.20 m.

Objectives — Students can: (1) state that field lines leave the north pole and enter the south, are closer where the field is stronger and never cross, and sketch the field of a bar magnet and of two facing poles; (2) use F=BIL to get 0.20 N from 0.40 T, 2.5 A and 0.20 m, and say how the force changes when the current or the field is reversed; (3) use a 500 to 50 turns ratio to get 22 V from 220 V, and explain that an ideal transformer keeps power constant while current goes as the inverse ratio; (4) get 6.0 W input and 4.5 W mechanical output from 12 V and 0.50 A, giving 75 percent efficiency, and say where the loss goes.

01 Prerequisites (3-minute check)

If any of these fails, fix it before the lesson starts.

Skill Quick check Pass mark
Electric current What does 1 A mean One coulomb of charge passing each second
Unit of force How big is 1 N The force giving 1 kg an acceleration of 1 m/s2
Power What is 12 V times 0.50 A 6.0 W
Conservation of energy Does a transformer increase power when it raises voltage No, an ideal transformer has equal input and output power

02 Lesson flow (45 minutes)

Time Stage Tutor does Student does
0-6 min Open with one wrong answer A transformer drops 220 V to 22 V: does the current rise or fall Most say it falls, but it rises
6-18 min Act one: field and field lines Out of north, into south, denser means stronger, never crossing; a solenoid looks like a bar magnet Students sketch the field between two facing poles
18-30 min Act two: F=BIL and direction 0.40 times 2.5 times 0.20 gives 0.20 N; reversing the current or the field reverses the force Students use the left-hand rule on three cases
30-40 min Act three: transformers and motors 500 to 50 turns takes 220 V to 22 V and 2.0 A to 0.20 A; a motor takes 6.0 W and gives 4.5 W, so 75 percent Students check that power is conserved
40-45 min Three exit questions Mark on the spot and label formula, direction or power errors All three done independently

03 Teaching script (read it out)

Scene 1: Act one: field lines describe a field, they are not objects

Students draw field lines as arrows flying from one pole to the other, so they allow lines to cross and think more lines can be added freely. Give three rules: outside a magnet the lines leave the north pole and enter the south, and inside they close the loop; closer lines mean a stronger field, so the poles are densest; lines never cross, because a point can have only one field direction. Then show a solenoid: grip it with the right hand, fingers along the current, thumb to the north pole, and its field matches a bar magnet. That is the electromagnet.

Out of north, into south, denser means stronger, and they never cross.

Scene 2: Act two: the size uses three quantities, the direction uses two reversals

Students treat F=BIL as a size-only formula and leave direction blank. Teach two separate judgements: size is B times I times L, so doubling any one doubles the force; direction depends on current and field together, so reversing either reverses the force while reversing both leaves it unchanged. When the wire runs parallel to the field there is no force at all, so check the angle before substituting: 0.20 N holds only when they are perpendicular.

Multiply three quantities for the size, and watch only whether current or field is reversed.

Scene 3: Act three: a transformer changes voltage and current, never power

500 turns against 50 is a ten-to-one step down, so 220 V becomes 22 V, and the secondary current is ten times the primary: 2.0 A against 0.20 A, with 44 W on both sides. Make students say that pair out loud, because power is conserved. Real transformers lose energy in the core and windings, so at 90 percent efficiency 50 W in gives 45 W out and the rest becomes heat. A motor works the same way: 12 V times 0.50 A is 6.0 W of electrical input, but only 4.5 W of mechanical output appears, so 75 percent, with the loss in coil resistance and friction.

A transformer swaps the ratio, not the power; efficiency is always below one.

04 Question types and worked steps

Type Example Steps Answer
Force on a wire 0.40 T, 2.5 A, 0.20 m perpendicular, find the force F equals B times I times L after checking they are perpendicular 0.20 N
Angle case Same numbers but the wire meets the field at 30 degrees Multiply by sin 30, which is 0.5 0.10 N
Transformer 500 turns to 50, input 220 V, output 2.0 A, find output voltage and input current Voltage follows the turns ratio, current the inverse ratio 22 V and 0.20 A, 44 W on both sides
Motor efficiency 12 V at 0.50 A with 4.5 W mechanical output Input 6.0 W, output over input 75 percent
Sanity check (teach this): Four checks. First, units must work out: T times A times m gives N, and 0.40 times 2.5 times 0.20 is 0.20 N, so a result of 2 N means a decimal slip. Second, a wire parallel to the field feels no force, so never substitute blindly. Third, a step-down transformer must have the larger secondary current, so a smaller secondary current means the ratio was inverted. Fourth, every efficiency is below 100 percent, and the electrical input of a motor always exceeds its mechanical output, the gap becoming heat and sound.

05 Independent practice (3 questions)

Question Answer What to watch
Force on a wire 0.40 T, 2.5 A, 0.20 m, perpendicular Check the length was converted from cm to m
Angle case Same numbers at 30 degrees Check they used sin 30, not cos 30
Transformer 500 to 50, 220 V, 2.0 A Check both sides come to 44 W
Motor efficiency 12 V, 0.50 A, 4.5 W out Check the input was not written as 4.5 W

06 Common mistakes and what to say

Mistake Student writes Say this
Drawing field lines that cross Students draw two lines crossing between the poles and put an arrow at the crossing A field has one direction at each point, so lines never cross. Crossing would mean two directions at once, which cannot happen.
Believing a transformer multiplies power Students say 220 V to 22 V keeps the current, so the power falls and energy is wasted A transformer keeps power the same and simply trades voltage against current. 500 to 50 steps voltage down ten times and current up ten times, and both sides carry 44 W.
Ignoring the angle in F=BIL Students multiply the three numbers even when the wire runs parallel to the field Check the angle first. There is no force when they are parallel, the full formula applies only when perpendicular, and other angles take the sine.
Efficiency as output over output plus input Students compute 4.5 over 4.5 plus 6.0 and report 42.9 percent Efficiency has one form: output over input. 4.5 over 6.0 gives 75 percent, and the remaining 25 percent becomes coil heating and friction.

07 Homework (paper, section and question numbers)

08 Exit check (last 5 minutes)

Question Answer Decision
Field line rules All three rules in one go If crossing is missed, redo act one
F=BIL 0.20 N and how the force changes when the current reverses If they cannot, redo act two
Transformer and efficiency 22 V, 0.20 A, 44 W both sides, motor 75 percent If power is not conserved, redo act three

09 Tutor FAQ

Why can field lines never cross?

A magnetic field has a single direction at every point, so two lines meeting would give that point two directions at once, which contradicts the field itself.

Why does current fall when a transformer steps voltage up?

An ideal transformer keeps input and output power equal, so raising the voltage by a factor lowers the current by the same factor, which is why high-voltage transmission wastes less in the cables.

Can a motor reach 100 percent efficiency?

No. The coil has resistance, the bearings have friction and the core has eddy currents, so mechanical output is always less than electrical input.

Find a tutor — freeTutor Registration →

A TutorZone lesson-prep guide. Written by the TutorZone team; questions and lesson flow are original and are not taken from any school or publisher material.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →