S4 Chemistry Separation and Purification Practice 1 (Basics)
- 2026-11-17
S4 Chemistry Separation and Purification Practice 1 (Basics)
Ten items on choosing filtration, evaporation, distillation, a separating funnel or sublimation, plus simple percentage work.
Four properties decide the method Judge the state, solubility and boiling point of each component first, then pick a method; each item carries a one-line note.
01 Paper details (check answers afterwards)
| Item | Detail |
|---|---|
| Questions | 10 |
| Suggested time | 25 |
| Difficulty mix | Foundation 4 · Intermediate 2 · Challenge 2 · Error redo 2 |
| Chapter | Chapter: S4 Chemistry: separation and purification of mixtures |
| Level | Basics |
02 Questions (10 items)
- FoundationWhich type of mixture is filtration used to separate?
- Foundation250 g of sea water contains 3.5% salt. How much salt remains after the water is evaporated?
- FoundationWhich combination is simple distillation best used for?
- FoundationWhen a separating funnel is used for oil and water, how is the lower layer taken out?
- IntermediateA dye moves 3.2 cm while the solvent front moves 8.0 cm. What is its Rf value?
- Intermediate5.0 g of a mixture of ammonium chloride and sand is heated. The ammonium chloride sublimes and 3.2 g of sand remains. What percentage of the mixture was ammonium chloride?
- ChallengeIn the fractional distillation of petroleum, which fraction leaves the top of the column first?
- ChallengeDistillation of 60 cm3 of an ethanol-water mixture gives 45 cm3 of ethanol. What is the recovery?
- Error redoAfter filtering a mixture of salt water and sand, what is on the filter paper and what is in the filtrate?
- Error redoIs distillation a physical change or a chemical change?
03 Answers and one-line notes
| # | Answer | One-line note |
|---|---|---|
| 1 | An insoluble solid from a liquid, for example sand and water. | The pores of the filter paper let liquid and dissolved substances through while the solid stays behind. |
| 2 | 250 x 0.035 = 8.75 g. | Find the mass of solute first; evaporation only removes the water. |
| 3 | Liquids with different boiling points, or a solvent and a dissolved solid such as water and salt. | Heating vaporises the lower-boiling component first and the condenser turns the vapour back into liquid. |
| 4 | Open the tap and run the lower layer into a beaker; the upper layer is poured out of the top afterwards. | The two layers do not mix and the denser layer settles at the bottom. |
| 5 | Rf = 3.2 / 8.0 = 0.40. | Rf has no unit and always lies between 0 and 1. |
| 6 | (5.0 – 3.2) / 5.0 x 100 = 36.0%. | The loss in mass is the ammonium chloride, which changed straight from solid to gas. |
| 7 | The fraction with the lowest boiling point and smallest molecules, such as refinery gas and petrol. | The column is cooler towards the top, so low-boiling fractions condense higher up. |
| 8 | 45 / 60 x 100 = 75.0%. | Recovery compares what was collected with what was present at the start. |
| 9 | Sand is on the paper and salt water is in the filtrate. | A common error is to think filtration removes dissolved salt; it passes through with the filtrate. |
| 10 | A physical change. | No new substance is formed, only a change of state; heating alone does not make it a chemical reaction. |
04 What to do after marking
- After marking, redo only the wrong items and write down which step went wrong (formula, unit, or misread number).
- Repeat the same item two days later; move to the next paper only when both attempts are correct.
- Parents only need the answer and note columns; there is no need to explain every item.
Download the full ten-item paper as a PDF, answers and notes included.Tutor Registration →
Questions and answers are written originally by the TutorZone team and are not taken from any school, publisher or examination authority paper. Every value is checked by computer.



