/en-tutor-prep-s4-physics-basic-electronics/
/en-tutor-prep-s4-physics-basic-electronics/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

Physics S4 | Basic Electronics Revision Guide for Tutors | Start with the diode, then dividers and switches

Physics S4 | Basic Electronics Revision Guide for Tutors | Start with the diode, then dividers and switches

  • 2026-11-22

Students can draw the circuit but asked for the current through a 2 volt LED fed from 5 volts through 220 ohms, half of them simply divide 5 by 220, because they have not learned to take the LED drop away first.

Objectives — By the end the student can: state that a diode conducts forward and blocks reverse, and compute current after subtracting the drop, so 5 volts through 220 ohms into a 2 volt LED gives 13.6 milliamps and 27.3 milliwatts in the LED; use a potential divider to get 9 volts from 12 volts with 2 and 6 kilo ohms, and explain that only the ratio matters; use the negative temperature coefficient of a thermistor to explain an output falling from 4.5 volts to 1.5 volts; and explain half wave rectification leaving a 5.3 volt peak from a 6 volt peak input, plus a transistor turning 1.00 milliamps of base current into a switch for an 80 milliamp relay.

01 Prerequisites (3-minute check)

If any of these fails, fix it before the lesson starts.

Skill Quick check Pass mark
Ohm law How do you find the current through two resistors in series? Add the resistances, then divide the supply by the total
Fractions and ratio In 12 volts, what fraction is 6 kilo ohms of 2 plus 6 kilo ohms? Three quarters, which is 9 volts
Electrical power 2 volts at 14 milliamps is how much power? About 28 milliwatts

02 Lesson flow (60 minutes)

Time Stage Tutor does Student does
0-6 min Prior check Ohm law, ratio, power Two of three right before moving on
6-16 min Diode and LED A 0.7 volt forward drop, reverse blocking, series resistor Student gets 13.6 milliamps
16-26 min Potential divider Output is input times the lower arm share Student gets 9 volts
26-36 min Sensing components Hotter thermistor means less resistance, brighter LDR means less resistance Student explains 4.5 to 1.5 volts
36-46 min Rectification and smoothing Half wave keeps a 5.3 volt peak, a capacitor fills the dips Student says why the capacitor raises the average
46-54 min Transistor as a switch 1.00 milliamps of base current switches the relay Student explains saturation
54-60 min Exit check Ask why an LED always needs a resistor Without it the current destroys the LED

03 Teaching script (read it out)

Scene 1: Diode: subtract the drop, then divide

The single idea is one way conduction: forward biased it conducts with about a 0.7 volt drop in silicon, reverse biased it blocks almost completely. Have them write the model, a switch in series with a fixed drop, as the first line of their notes, because every later question leans on it.

The LED sum is subtract then divide: 5 minus 2 leaves 3 volts across 220 ohms, giving 13.6 milliamps and 27.3 milliwatts in the LED itself. They should also be able to say that without the resistor the current is limited only by the supply, so the LED is destroyed. That sentence is a standard explanation mark.

Add three practical details that make the topic feel real: the long leg is the anode, different colours drop different voltages, roughly 2 volts for red and 3 for blue, and a series resistor is compulsory. Lighting and decorations in their own homes become the hook.

Student must say: why can you not just divide 5 volts by 220 ohms for a 2 volt LED?

Scene 2: Potential divider: one expression, half the paper

There is one expression: output equals input times the lower arm over the sum of both arms. For 12 volts with 2 kilo ohms above and 6 kilo ohms below, the output is 12 times three quarters, which is 9 volts. Make them label the upper and lower arm on the diagram before substituting, and they will stop inverting the fraction.

Then add sensing. A thermistor has a negative temperature coefficient, so resistance falls as temperature rises. With 9 volts, a fixed 10 kilo ohm and a thermistor of 10 kilo ohm at 20 degrees, the output is exactly half, 4.5 volts; at 60 degrees the thermistor is 2 kilo ohm and the output falls to 1.5 volts. Ask them to explain why a hotter sensor gives a lower output, because the reasoning outlives the number.

An LDR follows the same logic with light instead of heat. Put it in the lower arm and it gives a high output in the dark, which suits a night light; put it in the upper arm and the sense reverses. That choice of position is exactly what design questions test.

Student must say: 12 volts with 6 kilo ohms above and 2 kilo ohms below gives what output?

Scene 3: Rectification, smoothing and the transistor switch

Turning alternating into direct current uses a diode. A 6 volt peak input through half wave rectification leaves a 5.3 volt peak, because every positive half cycle pays the 0.7 volt drop first. Have them sketch input and output together so the missing half and the lost 0.7 volts are both visible.

Smoothing uses a capacitor: it charges at the peak and discharges into the load through the dips, so the waveform flattens. They should be able to state that a larger capacitor or a lighter load gives smaller ripple, which is the practical mark.

A transistor is an electronic switch: 5 volts through 4.3 kilo ohms minus 0.7 volts gives 1.00 milliamps of base current, which could support 0 milliamps of collector current while the relay needs only 80, so the transistor is driven into saturation and behaves as a closed switch. Stress that saturation is the intended state here, not a fault.

Student must say: why use a transistor instead of a variable resistor to drive a relay?

04 Question types and worked steps

Type Example Steps Answer
LED current 5 volts, LED 2 volts, 220 ohms Subtract the drop, then divide 13.6 milliamps
Divider output 12 volts, 2 kilo ohms above, 6 below Input times lower arm share 9 volts
Thermistor divider 9 volts, fixed 10 kilo ohms, thermistor 2 kilo ohms Substitute the lower arm 1.5 volts
Half wave peak 6 volt peak input Peak minus the forward drop 5.3 volts
Base current 5 volts through 4.3 kilo ohms, 0.7 volt base emitter Subtract 0.7 then divide 1.00 milliamps
Sanity check (teach this): Three sanity checks: an output can never exceed the input, so more than 12 volts means the arms were swapped; current in a diode circuit must run from the positive rail to the negative, so a negative answer means the assumed direction is wrong; and the collector current cannot exceed gain times base current, so 500 milliamps from 1 milliamp means the gain was not applied.

05 Independent practice (3 questions)

Question Answer What to watch
LED current 9 volts, LED 3 volts, 300 ohms 20 milliamps
Divider output 9 volts, 3 kilo ohms above, 6 below 6 volts
LDR behaviour LDR in the upper arm at dusk Output falls, because the upper resistance rises

06 Common mistakes and what to say

Mistake Student writes Say this
Forgetting the diode drop Answering 5 volts over 220 ohms is 22.7 milliamps The diode takes 0.7 volts, or the LED takes its 2 volts, and only the rest appears across the resistor. Begin every such answer with the resistor voltage equals supply minus drop.
Inverting the divider arms Answering 3 volts when the correct answer is 9 volts The output is always the lower arm share. Label which resistor the output is across before substituting.
Thinking a hot thermistor has more resistance Answering that output rises with temperature The usual thermistor has a negative coefficient, so resistance falls as it warms, and an output taken across it falls too. The student should give the reason, not just the trend.
Treating the transistor as unlimited gain Answering that 1 milliamp of base current gives 1 amp Collector current is limited by the load and the supply and stops at saturation. 1 milliamp times 100 is a ceiling, and the relay resistance sets the real value.

07 Homework (paper, section and question numbers)

08 Exit check (last 5 minutes)

Question Answer Decision
Diode Forward conducts with a drop, reverse blocks Saying it conducts both ways means redraw the waveform
Divider Output is input times the lower arm share Swapped arms mean redo the sum
Transistor A small base current controls a large collector current Saying it amplifies voltage means redo the relay question

09 Tutor FAQ

Why must an LED have a series resistor

The forward drop of an LED is nearly fixed, so connected directly the current is limited only by the supply and far exceeds the rating. The resistor absorbs the surplus voltage and sets a safe current.

Why is a potential divider unsuitable for powering a heavy load

Its output depends on the ratio of the two resistors. A load connected across the lower arm changes that ratio, so the output sags. Dividers are for signals, not for supplying power.

Why add a capacitor after rectification

Rectification only removes the negative half, leaving a pulsing output. The capacitor charges at the peak and discharges through the dips, flattening the waveform so the following circuit sees a steadier voltage.

Find a tutor — freeTutor Registration →

A TutorZone lesson-prep guide. Written by the TutorZone team; questions and lesson flow are original and are not taken from any school or publisher material.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →