S5 Chemistry (DSE) | Calorimetry Lesson Prep Guide | Measuring Enthalpy of Neutralisation and Combustion
- 2026-11-21
Students can recite q = mcDT yet use the mass of water for the mass of solution, and read the highest thermometer value as the final temperature; on combustion they recall the formula but cannot say why the cup is insulated or why container heat uptake matters. This lesson reduces calorimetry to three checkable moves: every quantity has a source, the temperature rise comes from a graph, and heat losses are listed one by one.
01 Prerequisites (3-minute check)
If any of these fails, fix it before the lesson starts.
| Skill | Quick check | Pass mark |
|---|---|---|
| Moles and concentration | How many moles are in 25 cm3 of 0.5 mol dm-3 solution | 0.0125 mol |
| Specific heat capacity | The value and unit for water | 4.2 J g-1 K-1 |
| Conservation of energy | How heat released relates to the temperature rise | Heat released equals mcDT absorbed |
02 Lesson flow (60 minutes)
| Time | Stage | Tutor does | Student does |
|---|---|---|---|
| 0-6 min | Label the formula | Pin m, c and DT back onto the apparatus diagram | Write the source of each quantity beside the diagram |
| 6-20 min | Extrapolate the rise | Model two trend lines meeting at the moment of mixing | Draw the extrapolation and read the value |
| 20-34 min | Neutralisation | Compute q from the rise, divide by moles of water formed | Complete one data set with sign and unit |
| 34-46 min | Combustion | Compare both set-ups and locate each heat loss | Mark three heat loss points on the diagram |
| 46-55 min | Error diagnosis | Give one high and one low result, ask for a cause each | Write one likely cause with its direction |
| 55-60 min | Exit check | Ask why their enthalpy change is negative | Answer in one sentence linking heat release to sign |
03 Teaching script (read it out)
Scene 1: Source every quantity before substituting
Marks in calorimetry are lost before the arithmetic: wrong mass, wrong temperature rise, unconverted units. Draw the apparatus and have students pin m, c and DT onto the correct part, then ask whether each value was measured or assumed. Any quantity without a source does not go into the equation.
Model it: 25 cm3 of 0.5 mol dm-3 acid mixed with 25 cm3 of alkali gives a total solution mass of 50 g at an assumed density of 1 g cm-3. Say the word assumed out loud. Students who can name their assumptions start judging reliability on their own.
Each quantity has a source; none is guessed
Scene 2: The rise comes from a graph, not the peak
The thermometer lags, so by the time it peaks the mixture is already cooling. Plot temperature against time, draw a trend line through the rising section and another through the cooling section, and read the intersection. That intersection is the temperature at mixing, and the difference from the start is DT.
Be precise about what extrapolation fixes: it corrects for the response time of the instrument, not for heat loss during the reaction. Keep the two separate or students will write the error analysis in the wrong direction.
Extrapolation gives the mixing instant, which is what the heat belongs to
Scene 3: Count heat losses as a list
A combustion set-up loses heat through the flame heating the container, the container absorbing heat, incomplete combustion, water vapour carrying latent heat, and losses to the air. Do not say there is some error; have students point at each location and decide whether it makes the result too high or too low.
Then push: what happens with a copper cup? Copper conducts heat away faster, so more is lost, but the copper itself absorbs less. The two effects pull in opposite directions, which is exactly the reasoning this chapter is testing.
Error analysis is a list, not a sentence
04 Question types and worked steps
| Type | Example | Steps | Answer |
|---|---|---|---|
| Neutralisation | 50 cm3 of mixed solution rises 3.4 C, 0.05 mol water formed | Apply q = mcDT, divide by moles, state the sign | q = 50 x 4.2 x 3.4 = 714 J, enthalpy change -14.3 kJ mol-1, density assumed |
| Combustion | 0.50 g ethanol raises 200 g water by 18 C | Heat gained by water, convert per mole, list assumptions | q = 15.1 kJ, 0.0109 mol ethanol, about -1390 kJ mol-1, container uptake ignored |
| Specific heat capacity | Given heater power and time, find c of a metal block | Electrical energy equals heat, solve for c, check units | c = Pt / (mDT), unit must be J g-1 K-1 |
| Data handling | Given a temperature-time table, find the mixing temperature | Plot, extrapolate, read the intersection | The intersection, not the largest tabulated value |
05 Independent practice (3 questions)
| Question | Answer | What to watch |
|---|---|---|
| Source the quantities | Give a neutralisation set-up diagram and one data set | Check that each quantity has a stated source and unit |
| Extrapolate | Give twelve time-temperature readings | Check that two trend lines are drawn and the intersection read |
| Error direction | Ask whether a poorly insulated cup makes the result high or low | Check the reasoning: heat loss lowers the rise and the magnitude |
06 Common mistakes and what to say
| Mistake | Student writes | Say this |
|---|---|---|
| Wrong mass | Substituting 50 g as the mass of water only | The solution is acid plus alkali; where did your 50 g come from? |
| Peak read as final | Highest table value minus starting value | The thermometer lags, so the peak is already after cooling; extrapolate to the mixing instant |
| Positive enthalpy change | Reporting 14.3 kJ mol-1 and stopping | Exothermic means negative; miss the sign and every later step is wasted |
| No assumptions | A full answer with no stated assumption | Density 1 g cm-3 and no heat loss are assumptions; state them so the marker sees the reasoning |
07 Homework (paper, section and question numbers)
- Secondary chemistry index — Every chapter in this subject
- Lesson prep index — Matching chapters in other subjects
- Redo this chapter — Independent practice 1-3: source the quantities, extrapolate, error direction
08 Exit check (last 5 minutes)
| Question | Answer | Decision |
|---|---|---|
| Three quantities | m, c and DT each sourced | No source means redo the labelling drill |
| Extrapolation | Mixing instant, not the peak | Peak reading means redraw the graph |
| Sign and unit | Negative, kJ mol-1 | Missing sign or unit means rewrite the whole answer |
09 Tutor FAQ
Their answer is far from the literature value
Check moles first, then whether DT came from extrapolation. School calorimeters lose heat, so a ten to twenty per cent low result is normal; what matters is that the direction is explained.
Must they draw the graph
Yes. Extrapolation is the only technique-based skill in this chapter and has been examined directly; students who skip the graph almost always lose those marks.
Do they need a bomb calorimeter
Not the hardware, but they should know a sealed constant-volume vessel with known water mass gives a more accurate value, and that it reduces both heat loss and incomplete combustion.
Find a tutor — freeTutor Registration →
A TutorZone lesson-prep guide. Written by the TutorZone team; questions and lesson flow are original and are not taken from any school or publisher material.



