/en-tutor-prep-s6-chemistry-industrial-process-conditions/
/en-tutor-prep-s6-chemistry-industrial-process-conditions/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

S6 Chemistry | Industrial Processes and Condition Choices Prep Guide (Tutor Use) | Four zones, Haber conditions, yields of 75 and 95 per cent

S6 Chemistry | Industrial Processes and Condition Choices Prep Guide (Tutor Use) | Four zones, Haber conditions, yields of 75 and 95 per cent

  • 2026-11-17

Most students can recite high temperature, high pressure, catalyst, then stall when asked why 450 C rather than 600 C, and never mention recycling unreacted gas. This lesson takes the Haber and Contact processes, splits a plant into pre-treatment, reaction, separation and recycle, then uses a feed of 100 mol nitrogen and 300 mol hydrogen to reach 200 mol theoretical ammonia, 150 mol actual and a 75 per cent yield, ending with where 13.8 MJ of heat goes.

Objectives — Students can: (1) draw the four-zone flow and name one piece of equipment in each zone; (2) explain the Haber conditions of 450 C and 200 atm and the Contact conditions of 450 C and 1 to 2 atm using four yardsticks of rate, equilibrium, cost and safety; (3) calculate 200 mol theoretical ammonia from 100 mol nitrogen and 300 mol hydrogen, 150 mol actual and a 75 per cent yield, plus 100 mol of recycled gas made of 25 mol nitrogen and 75 mol hydrogen; (4) multiply 150 mol by 92 kJ per mol to obtain 13.8 MJ and name one use for that heat.

01 Prerequisites (3-minute check)

If any of these fails, fix it before the lesson starts.

Skill Quick check Pass mark
Le Chatelier principle What does raising pressure do to the nitrogen and hydrogen equilibrium It shifts towards fewer gas moles, raising the ammonia share
Role of a catalyst Does an iron catalyst move the equilibrium position No, it only shortens the time to reach equilibrium
Limiting reagent Which runs out first, 100 mol nitrogen or 300 mol hydrogen Neither, they match the one to three ratio and run out together
Percentage yield Theoretical 200 mol, actual 150 mol, what is the yield 75 per cent

02 Lesson flow (45 minutes)

Time Stage Tutor does Student does
0-6 min Four opening questions Name the four zones, the Haber conditions, whether a catalyst moves equilibrium, and 150 divided by 200 Oral answers while the tutor draws the flow left to right
6-20 min Act one: split the plant into four zones Pre-treatment compresses and removes sulphur and water, reaction is the iron catalyst bed, separation condenses ammonia by cooling under pressure, recycle returns unreacted gas Students draw the flow and name one item per zone
20-34 min Act two: four yardsticks for conditions 450 C balances rate against equilibrium, 200 atm balances equilibrium against compression cost, the iron catalyst buys time only Students state what happens if each condition rises and falls
34-42 min Act three: yield, recycle and heat 200 mol theoretical, 150 mol actual, 75 mol nitrogen and 225 mol hydrogen consumed, 100 mol recycled, and 150 times 92 kJ gives 13.8 MJ Students calculate with units written down
42-45 min Exit check Three questions marked on the spot, each tagged to flow, condition or calculation Independent work

03 Teaching script (read it out)

Scene 1: Act one: a plant is a four-zone line, not a single reaction

Students equate industrial ammonia production with one reaction and leave the pre-treatment question blank. Have them write four boxes across the page: pre-treatment compresses the feed to 200 atm and removes sulphur and water because the catalyst is poisoned by sulphur; reaction is the iron bed where only part of the gas converts; separation cools and compresses so ammonia condenses, since its boiling point is far above those of hydrogen and nitrogen; recycle returns 25 mol nitrogen and 75 mol hydrogen. The order cannot be swapped, because separation must follow reaction and recycle must follow separation.

Fixed order: pre-treatment, reaction, separation, recycle.

Scene 2: Act two: every condition is a compromise between two yardsticks

Raising temperature speeds the reaction but shifts an exothermic equilibrium backwards; raising pressure shifts equilibrium forward and speeds the rate, but compression power and vessel thickness cost rise sharply at 200 atm; a catalyst lowers activation energy without moving equilibrium or lifting the maximum yield. Haber takes 450 C and 200 atm as a compromise among rate, equilibrium and cost, while the Contact process needs only 1 to 2 atm because sulphur dioxide already converts almost fully at atmospheric pressure. Ask students what happens if the condition is not set this way, which is far more useful than memorising numbers.

Every condition must be explained in pairs: the cost of raising it and the cost of lowering it.

Scene 3: Act three: yield is a division, not a feeling

100 mol nitrogen and 300 mol hydrogen match the one to three ratio, so the theoretical yield is 200 mol ammonia; 150 mol actual divided by 200 gives 75 per cent. The reactor outlet still holds 25 mol nitrogen and 75 mol hydrogen, 100 mol in total, and discarding it would waste half the feed for every 150 mol of ammonia made. Each mole of ammonia releases 92 kJ, so 150 mol releases 13.8 MJ, which preheats the gas entering the catalyst bed through the heat exchanger. Require units beside every answer, because a missing mol, kJ or per cent means an incomplete answer.

Yield is actual over theoretical, heat is moles times enthalpy per mole.

04 Question types and worked steps

Type Example Steps Answer
Explain a condition Why does the Haber process use 450 C rather than 600 C Use the rate and equilibrium yardsticks and state both consequences 450 C is the compromise, 600 C is faster but the equilibrium yield collapses
Complete the flow Name the operation that follows separation Follow the four-zone order without skipping Unreacted gas returns to the reactor
Calculate yield 150 mol actual against 200 mol theoretical Confirm the limiting reagent, then divide by the theoretical amount 75 per cent
Calculate heat How much heat does 150 mol of ammonia release Multiply moles by 92 kJ per mol 13,800 kJ, that is 13.8 MJ
Sanity check (teach this): Four checks: the four zones must appear in the order pre-treatment, reaction, separation, recycle, and a missing zone means the flow is not understood; condition answers must state the cost of raising and the cost of lowering, and saying only that it speeds things up earns half marks; the yield denominator must be the theoretical amount from the limiting reagent, because using total feed produces absurd answers above 100 per cent; heat figures must carry units and match the mole count, so 150 times 92 gives 13,800 kJ, while 13,800 J or 138 MJ are order-of-magnitude errors.

05 Independent practice (3 questions)

Question Answer What to watch
Draw four zones Four zones with one item of equipment each Any missing zone or wrong order
Explain a condition Pick one condition and use both yardsticks Is it only about speed
Calculate yield From 100 and 300 mol to 75 per cent Is the denominator the limiting theoretical amount
Calculate heat 150 mol times 92 kJ Are units kJ and reduced to MJ

06 Common mistakes and what to say

Mistake Student writes Say this
Catalyst treated as a yield booster Answer says adding a catalyst raises the yield A catalyst only shortens the time to equilibrium, leaving position and final yield unchanged. The right answer is that it keeps the rate usable at 450 C, which protects the equilibrium yield.
Assuming hotter is always better Answer says raising temperature shifts equilibrium right The forward reaction is exothermic, so heating shifts equilibrium left and lowers the yield. Heat buys rate only, which is why 450 C is a compromise rather than a maximum.
Yield divided by total feed 150 mol from 400 mol of feed written as 37.5 per cent Divide by the 200 mol theoretical amount from the limiting reagent to get 75 per cent. Using total feed counts unreacted hydrogen as loss, which looks neat but means something else.
Recycle forgotten Answer stops once ammonia is separated The outlet still holds 25 mol nitrogen and 75 mol hydrogen, so venting it throws away half the feed. Industry always returns it to the reactor.

07 Homework (paper, section and question numbers)

08 Exit check (last 5 minutes)

Question Answer Decision
Four zones Order plus one item of equipment per zone A missing zone means re-teaching act one
Condition trade-offs The cost of raising and of lowering each condition Speed only means re-teaching act two
Yield and heat 75 per cent and 13.8 MJ with units Wrong units mean re-teaching act three

09 Tutor FAQ

Must students memorise 450 C and 200 atm?

The numbers matter, but marks come from justifying them. A condition answer with no reason usually earns half the marks.

Why is the Contact process pressure lower?

Sulphur dioxide already converts over ninety per cent at atmospheric pressure and 450 C, so extra pressure adds cost and equipment demands without much gain, hence 1 to 2 atm.

Does recycled gas build up indefinitely?

No. The recycled nitrogen and hydrogen convert a little on each pass and the ammonia is removed, so the recycle settles near 100 mol in steady operation.

Find a tutor — freeTutor Registration →

A TutorZone lesson-prep guide. Written by the TutorZone team; questions and lesson flow are original and are not taken from any school or publisher material.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →