Junior Science (S2)|Forces, Motion and Simple Machines — Lesson-Prep Guide for Tutors|Resultant force, friction, levers, pulleys
- 2026-11-21
Students say a push makes things move, then fill in any direction for the resultant and assume every pulley halves the effort. This lesson builds three habits: draw the force diagram, compute the moment, ask where the energy went.
01 Prerequisites (3-minute check)
If any of these fails, fix it before the lesson starts.
| Skill | Quick check | Pass mark |
|---|---|---|
| Weight and the newton | What does a 60 kg student weigh, taking g as 10 | 600 N, mass times ten |
| Multiplying decimals | What is 300 times 0.2 | 60, in newton metres |
| Speed and distance | If the same journey takes twice as long, what happens to speed | It halves, the distance is unchanged |
02 Lesson flow (60 minutes)
| Time | Stage | Tutor does | Student does |
|---|---|---|---|
| 0-5 min | Opening question | Pushing a heavy desk that will not move versus an empty one: what is different | Hands up, and the word friction must appear |
| 5-18 min | Act 1: resultant and friction | Draw 45 N right and 12 N left and ask for the resultant | Write 33 N to the right with the direction |
| 18-33 min | Act 2: lever moments | 300 N at 0.2 m: what force is needed at 0.6 m | Compute 100 N and state an advantage of 3 |
| 33-45 min | Act 3: pulleys and ramps | A movable pulley halves the force but doubles the rope; a 4 m ramp rises 0.8 m | Get 120 N and 1.2 m; 80 N and 80 per cent |
| 45-54 min | Independent practice | Circulate, correcting only moment arms and the energy claim | Finish three questions with working |
| 54-60 min | Exit check | Mark on the spot; two wrong means reteaching Act 3 | Self-assess and note the act to review |
03 Teaching script (read it out)
Scene 1: Force is a vector, so the resultant needs a direction
Force has size and direction, so two forces never simply add. 45 N right against 12 N left leaves 33 N right; forces in the same direction add, opposite forces subtract, and the direction follows the larger one. Draw a dot for the object and arrows for size and direction. That single habit removes most junior errors.
Then separate three cases. A zero resultant means at rest or moving at constant speed, not no forces: a book on a table feels 600 N of weight and 600 N of support. A non-zero resultant means the motion changes, and its direction is the direction of the resultant, not of the motion: a braking car still moves forward while the resultant points back. Add that friction always opposes relative motion, so a desk that will not move has friction equal to the push, not zero.
Add or subtract by direction, zero resultant is not zero force, friction opposes relative motion.
Scene 2: Moment balance is bookkeeping
One rule runs every lever: moment on the left equals moment on the right, and moment is force times the perpendicular distance from the pivot to the line of action. A 300 N load 0.2 m from the pivot gives 60 N m; with a 0.6 m arm the effort is 100 N. Load over effort gives the mechanical advantage, 300 over 100, which is 3.
Two things must stick. The moment arm is not the length of the rod but the perpendicular distance, so a slanted pull needs the perpendicular component. And a large advantage is not free energy: the force is three times smaller while the distance moved is three times larger. Close with real contrast: a bottle opener is a force multiplier that needs a long sweep of the hand, chopsticks are a speed and precision tool that lose force. Both are trades under the same moment rule.
Moment is force times perpendicular arm, both sides equal, and no machine gives free work.
Scene 3: Pulleys and ramps: go through energy, do not memorise
A single movable pulley lifts 240 N with 120 N of effort, but the rope must be pulled 1.2 m to raise the load 0.6 m, so the work is 72 J either way. A fixed pulley only changes direction and saves no force, which is the confusion students bring: they see a pulley and write half. A ramp is the same trade: 4 m long rising 0.8 m gives an advantage of 5, so a 400 N load needs 80 N, and the ideal input work of 80 times 4 is 320 J, equal to the gain of 400 times 0.8.
Real machines have friction, so the input work exceeds the useful work. If the actual input is 400 J, efficiency is 320 over 400, which is 80 per cent. Always give all three numbers: the force fell to 80 N, the distance rose to 4 m, and the efficiency fell below 100 per cent. A student who can describe any machine with those three numbers will stop asking which machine is best, because the answer is that there is only a trade.
Less force means more distance, efficiency stays below 100 per cent, give all three numbers.
04 Question types and worked steps
| Type | Example | Steps | Answer |
|---|---|---|---|
| Resultant force | 45 N right and 12 N left: what is the resultant | Subtract on the same line and follow the larger force | 33 N to the right |
| Moment balance | 300 N at 0.2 m against a 0.6 m arm | Moments equal on both sides | 100 N, advantage of 3 |
| Pulley advantage | A single movable pulley with a 240 N load | Halve the load, double the rope | 120 N, 1.2 m of rope |
| Ramp efficiency | 4 m long, 0.8 m high, 400 N, 400 J actually used | Advantage is length over height, then useful over input work | 80 N and 80 per cent |
05 Independent practice (3 questions)
| Question | Answer | What to watch |
|---|---|---|
| A 50 kg student stands on the ground and a lift floor pushes up with 550 N. What is the weight, and what is the resultant? | Weight 500 N, resultant 50 N upwards | Was the weight computed before subtracting, and is the direction up |
| A lever has its pivot at one end, 240 N at 0.3 m and a hand at 0.9 m. What force is needed, and what is the advantage? | 80 N and an advantage of 3 | Are the moments equal, measured from the pivot |
| A 600 N box is pushed up a 3 m ramp to a 0.6 m platform using 300 J. What is the efficiency? | Useful work 360 J, so 120 per cent is impossible and the data must be wrong | Efficiency above 100 per cent means an error in data or working |
06 Common mistakes and what to say
| Mistake | Student writes | Say this |
|---|---|---|
| Adding forces as plain numbers | 45 and 12 give 57 N | Forces have direction, so opposite ones subtract. Adding them assumes both push the same way; drawing the arrows shows one pointing left. |
| Using the rod length as the arm | Multiplying by the whole rod when the pivot is at one end | The moment arm runs from the pivot perpendicular to the line of action, and a slanted pull needs its perpendicular part. Using the full length overstates the moment. |
| Halving for every pulley | Writing 120 N for a fixed pulley with a 240 N load | A fixed pulley only changes direction, so the effort equals the load. Count the rope segments holding the movable pulley: one segment means no gain, two means half. |
| Assuming less force means less work | Saying the ramp makes the work smaller because it feels lighter | The smaller force is paid for with a longer distance. The 4 m ramp at 80 N is 320 J and lifting 0.8 m at 400 N is also 320 J; friction makes the real input larger. |
07 Homework (paper, section and question numbers)
- Build an equal-arm lever from a ruler and coins, record the distances at balance, and check that both moments are equal — Hand in a table with force, arm and moment columns
- Find three simple machines at home, and for each say whether it saves force and what the cost is — One line each, naming the trade
- Draw a force diagram for a 5 kg school bag at rest and state the resultant — Arrows with values, and a zero resultant
08 Exit check (last 5 minutes)
| Question | Answer | Decision |
|---|---|---|
| 20 N right and 8 N left: what is the resultant? | 12 N to the right | Wrong means reteaching Act 1 |
| What is a moment, and what is its unit? | Force times perpendicular arm, in newton metres | Wrong means reteaching Act 2 |
| A movable pulley lifts 300 N. What effort, and how much rope to raise it 0.5 m? | 150 N and 1 m of rope | Wrong means reteaching Act 3 |
09 Tutor FAQ
Do students need to memorise formulas?
Only two: resultant by direction, and moment as force times perpendicular arm. Pulleys and ramps follow from conservation of energy, and anything derived is never misremembered.
Acceleration is not taught in S2, so can we discuss it?
Discuss direction, not the calculation. Saying the motion changes in the direction of the resultant is enough; a equals F over m waits for S3.
Is there practice to set?
Yes. The homework links the physics index and related chapters, all free without sign-up, and every question asks for working and units.
Find a tutor — freeTutor Registration →
A TutorZone lesson-prep guide. Written by the TutorZone team; questions and lesson flow are original and are not taken from any school or publisher material.



