/en-tutor-prep-s4-physics-potential-divider-sensors/
/en-tutor-prep-s4-physics-potential-divider-sensors/
General Inquiry: info@TutorZone.com.hk
Office Hours: Monday to Saturday - 9:00 AM to 6:00 PM
WhatsApp Monday to Sunday - 24 hours
Hotline: +852 6828 1809
Instant Support: +852 9061 3106

Senior Physics | Potential Dividers and Sensors Teaching Guide | Current first, then how the voltage splits

Senior Physics | Potential Dividers and Sensors Teaching Guide | Current first, then how the voltage splits

  • 2026-11-22

Students can recite that voltage divides in series, then lose it completely at an LDR: they treat a larger resistance as a larger output voltage, without asking which resistor the output is measured across.

Objectives — By the end the student can: (1) state that series current is the same everywhere, so voltage divides in proportion to resistance, and write V out equals V in times R2 over R1 plus R2; (2) calculate that 12 volts across 10 kilohms and 4.7 kilohms gives 3.84 volts at 0.82 milliamps; (3) state that an LDR falls in resistance as light rises and an NTC thermistor falls as temperature rises, and calculate the fixed resistor voltage moving from 0.089 to 8.18 volts; (4) subtract a 0.7 volt diode or 2.0 volt LED forward drop before sizing a series resistor, then check I squared R against a quarter watt.

01 Prerequisites (3-minute check)

If any of these fails, fix it before the lesson starts.

Skill Quick check Pass mark
Ohm law What current flows through 10 kilohms at 12 volts? 0.82 milliamps
Series current Do two series resistors carry the same current? Yes, there is only one path
Power What power is dissipated by 0.015 amps through 470 ohms? 0.104 watts

02 Lesson flow (60 minutes)

Time Stage Tutor does Student does
0-6 min Prerequisite check Ohm law, series current, power Two of three correct before starting
6-16 min Where the divider formula comes from Same current, so voltage follows resistance Student derives it from Ohm law
16-28 min Two-resistor calculation V out equals V in times R2 over R1 plus R2 Student reaches 3.84 volts
28-38 min LDR as a light switch More light, less resistance, output rises Student names the resistor the output is across
38-46 min NTC thermistor Hotter means less resistance, negative coefficient Student reaches 4.29 volts
46-56 min Diode and series resistor Subtract the forward drop first Student reaches 470 ohms and 0.104 watts
56-60 min Exit check What happens to the output when it gets dark? It rises, because that resistor now takes more of the voltage

03 Teaching script (read it out)

Scene 1: Derive the divider, do not memorise it

Draw 12 volts across two resistors. Ask whether the current is the same in both, then write I equals V in over R1 plus R2, which gives 0.82 milliamps. The voltage across R2 is then I times R2, which is 3.84 volts.

Combine the two steps and the divider formula appears. Make every student derive it once, because the standard error is putting R1 in the numerator. The quick test is the extreme case: with R2 equal to zero the output must be zero, so a formula returning 12 volts has the wrong numerator.

Then ask what happens when R2 is far larger than R1: the output approaches the supply. That single sentence, the larger share of resistance takes the larger share of voltage, carries every sensor question that follows.

Student must say: which resistor belongs in the numerator, and why?

Scene 2: Sensors: decide which resistor the output is across

Put the LDR on top and a fixed 10 kilohm below, with the output across the fixed resistor. Bright light drops the LDR from 1 megohm to 1 kilohm, so the output climbs from 0.089 to 8.18 volts. This is the circuit inside a street lamp or a backlit clock.

Insist that every answer starts by circling the resistor the output is measured across. Move the output to the LDR itself and the trend reverses, which is how the same circuit can switch a lamp on at dusk or sound a buzzer at dawn. Two minutes on that contrast saves a whole topic of confusion.

Treat the thermistor the same way but spell out NTC: negative temperature coefficient, so resistance falls as temperature rises. At 25 degrees it reads 10 kilohms, at 50 degrees 4 kilohms, and with 6 volts and a fixed 10 kilohm below, the output rises from 3.00 to 4.29 volts. A hairdryer demonstration fixes the word negative for good.

Student must say: for an NTC, which way does resistance go with temperature, and which way does the output go?

Scene 3: Diodes, LEDs and the series resistor

Teach one model: a conducting diode holds a fixed forward drop, about 0.7 volts for silicon and 2 volts for an LED. With 5 volts, a 220 ohm resistor and a diode, the resistor sees 4.30 volts, so the current is 19.5 milliamps. Forgetting the 0.7 volt drop is the most common lost mark here.

For an LED: 9 volts supply, 2 volts forward drop, 15 milliamps wanted, so R equals 7 over 0.015 which is 466.7 ohms. The nearest standard value is 470 ohms, giving 14.9 milliamps. Students should see that the calculated value is never what you buy.

Finish with the power check: I squared R gives 0.104 watts, safely inside a quarter watt. At 40 milliamps the same resistor passes 0.7 watts and will scorch. That check is what separates a top band answer from a correct one.

Student must say: why subtract the forward drop before sizing the resistor?

04 Question types and worked steps

Type Example Steps Answer
Divider output 12 volts, 10 kilohms and 4.7 kilohms, output across 4.7 V out equals V in times R2 over R1 plus R2 3.84 volts
Series current Same circuit I equals V in over total resistance 0.82 milliamps
LDR output 9 volts, fixed 10 kilohms, LDR 1 megohm to 1 kilohm Less resistance takes less voltage 0.089 to 8.18 volts
Series resistor 9 volts, 2 volt LED, 15 milliamps R equals supply minus drop over current 466.7 ohms, use 470
Sanity check (teach this): Three sanity checks: the divider output must be below the supply, so anything above 12 volts means a term is missing from the denominator; identify which resistor the output is across, because when it is the one whose resistance falls, the output falls with light or with temperature; a negative series resistance means the target current is impossible or the drop was copied wrongly, so re-read the supply voltage.

05 Independent practice (3 questions)

Question Answer What to watch
Divider output 9 volts, 6.8 kilohms on top, 3.3 kilohms below, output across the lower one About 2.94 volts
Thermistor output 6 volts, NTC 5 kilohms on top, fixed 10 kilohms below 4.00 volts
Series resistor 12 volts, 3.4 volt LED, 20 milliamps 430 ohms

06 Common mistakes and what to say

Mistake Student writes Say this
Wrong resistor in the numerator Answering 12 times 10 over 14.7, which gives 8.16 volts The numerator is the resistor the output is across. Circle it on the diagram before writing the formula.
Skipping the forward drop Answering 5 over 220, which gives 22.7 milliamps A conducting diode holds its drop, so the resistor only sees 4.30 volts and the current is 19.5 milliamps.
Believing an LDR rises with light Answering that a brighter light lowers the output An LDR falls in resistance as light rises, like an NTC with temperature. Write light up, resistance down, on the first page of notes.
Ignoring resistor power Answering that 470 ohms is fine because the value is right Check I squared R. 0.104 watts is safe, but a larger current exceeds a quarter watt and the resistor burns.

07 Homework (paper, section and question numbers)

08 Exit check (last 5 minutes)

Question Answer Decision
Divider formula V out equals V in times R2 over R1 plus R2, numerator is the measured resistor Using R1 means deriving it again
Sensor trends Light up resistance down, temperature up resistance down, output depends on where it is measured Reversing this means redrawing the circuit
Series resistor Subtract the forward drop, divide, then check I squared R Skipping the drop means redoing the power check

09 Tutor FAQ

Why is the series current the same everywhere

Charge cannot pile up inside a series circuit, so the same amount passes every cross section in the same time. That conservation is the only source of the divider formula.

Why choose 470 ohms instead of 466.7

Resistors come in standard series values. 470 ohms is the nearest value above the calculation, which draws slightly less current and is safer for the LED with no visible loss of brightness.

Can a divider be used as a power supply

Only to drive a high impedance input such as a comparator or a microcontroller pin. Feeding a motor or a lamp puts the load in parallel with the lower resistor and the output collapses.

Find a tutor — freeTutor Registration →

A TutorZone lesson-prep guide. Written by the TutorZone team; questions and lesson flow are original and are not taken from any school or publisher material.

Join as a tutor or coach — academic, music, sports, arts, STEM. Free to register. See how it works →